參數資料
型號： MAX2560EVKIT
廠商： Maxim Integrated Products, Inc.
英文描述： Evaluation Kits
中文描述： MAX2560、MAX2566、MAX2572評估板
文件頁數： 10/22頁
文件大小： 1937K
代理商： MAX2560EVKIT
E
WCDMA Mode
Perform the following steps to evaluate the MAX2566/
MAX2572 in the WCDMA mode:
1) Verify shunt JU24 is in the LOUMTS position.
2) With MAX2560/MAX2566/MAX2572 control software
active in the REG screen, use Tables 2 and 3 to set
the operating mode to WCDMA.
3) Connect the I and Q outputs of the arbitrary wave-
form generator to the I (J15) and Q (J16) ports. Set
the generator to WCDMA settings. Verify 300mV
peak baseband signal on Q+/Q- (JU2) and I+/I-
(JU1), or 600mV peak-to-peak differential.
4) The MAX2566 EV kit requires an external LO input.
Apply an external LO 1565MHz at -10dBm to the
LOH port.
5) Connect RFH0 (J1) to the spectrum analyzer.
Configure the spectrum analyzer to measure ACPR
for the uplink WCDMA. Set the center frequency to
1950MHz with 50MHz span and a +10dBm refer-
ence level.
6) Adjust the R1 (VGCRF) and R6 (VGCIF) (only adjust
VGCIF if VGS = 1) to obtain an output power of
+8dBm after accounting for cable and connector loss.
The ACPR in 3.84MHz bandwidth at ±5MHz offset
should be -49dBc, and the ACPR in 3.84MHz band-
width at ±10MHz offset should be -62dBc. Note that
C112–C115 are disconnected for this measurement.
GSM 900 Mode
Perform the following steps to evaluate the
MAX2566/MAX2572 in the GSM 900 mode:
1) Verify shunts JU23–JU26 and JU33 positions with
Table 4.
2) With MAX2560/MAX2566/MAX2572 control software
active in the REG screen, use Tables 2 and 3 to set
the operating mode to GSM 900 mode.
3) Connect the I and Q outputs of the arbitrary wave-
form generator to the I (J15) and Q (J16) ports. Set
the generator to GSM settings. Verify 300mV peak
baseband signal on Q+/Q- (JU2) and I+/I- (JU1), or
600mV peak-to-peak differential.
4) The MAX2566 EV kit requires an external LO input.
Apply an external LO 1190MHz at -10dBm to the
LOH port.
5) Connect GSM (J3) to the spectrum analyzer.
Configure the spectrum analyzer to measure spec-
tral mask for the GSM signal. Set the center fre-
quency to 900MHz with 50MHz span and a
+10dBm reference level.
MAX2560/MAX2566/MAX2572 Evaluation Kits
10
______________________________________________________________________________________
REGISTER (hex)
FRAC_SYNTH
FRAC
IF_N
IF_SYNTH
OPCTRL
CONFIG
TEST
CELLULAR CDMA
0B4FDF
020000
000497
00D830
09C01F
07A307
000025
PCS CDMA
0B4FDF
005555
000519
00D830
09F49F
07A307
000025
Table 1. MAX2560 Register Settings
REGISTER (hex)
FRAC_SYNTH
FRAC
IF_N
IF_SYNTH
OPCTRL
CONFIG
TEST
WCDMA
0B603B
03B13B
000302
00D80D
0DF77F
07A103
000025
GSM 900
0B602C
09D89E
000244
00D80D
0D876F
07BD007
000025
DCS 1800
0B602C
09D89E
000244
00D80D
0D876F
04BD0F
000025
GSM 1900
0B602C
09D89E
000244
00D80D
0D876F
04BD0F
000025
Table 2. MAX2566 Register Settings
相關PDF資料
PDF描述
MAX2572EVKIT Evaluation Kits
MAX2560 Evaluation Kits
MAX2566EVKIT Evaluation Kits
MAX260AMRG Microprocessor Programmable Universal Active Filters
MAX260BENG Microprocessor Programmable Universal Active Filters
相關代理商/技術參數
參數描述
MAX2566EGM 功能描述:調節器/解調器 RoHS:否 制造商:Texas Instruments 封裝 / 箱體:PVQFN-N24 封裝:Reel
MAX2566EGM-T 功能描述:調節器/解調器 RoHS:否 制造商:Texas Instruments 封裝 / 箱體:PVQFN-N24 封裝:Reel
MAX2566EVKIT 功能描述:射頻開發工具 RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
MAX256ASA 功能描述:功率驅動器IC RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX256ASA/V+T 制造商:Maxim Integrated Products 功能描述:3W PRIMARY-SIDE TRANSFORMER H-BRIDGE DRIVER FOR ISOLATED SUP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*