- 您現在的位置：買賣IC網 > PDF目錄385523 > MAX2204EVKIT (Maxim Integrated Products, Inc.) Evaluation Kit PDF資料下載
參數資料
| 型號： | MAX2204EVKIT |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Evaluation Kit |
| 中文描述： | MAX2204評估板 |
| 文件頁數： | 2/3頁 |
| 文件大?。?/td> | 93K |
| 代理商： | MAX2204EVKIT |
E
Connections and Setup
This section provides a step-by-step guide to operating
the EV kit and testing the device’s function.
Caution:
Do not turn on the DC power or RF signal genera-
tors until all connections are made:
1) Set the jumper (JP1) on the EV kit to ON. This
enables the device.
2) Connect a DC supply set to +2.85V (through a
DMM, if desired) to the VCC and GND terminals on
the EV kit. If available, set the current limit to 10mA.
Do not turn on the supply.
3) Connect the output (J3) to a DMM to measure output
voltage.
4) Set the signal generator output to +5dBm,
f = 836MHz. Using the power meter, determine the
actual output power of the signal generator.
5) Connect the signal generator to the SMA connector.
Do not turn on the signal generator.
6) Turn on the DC supply; the supply current should
read approximately 1.3mA.
7) Activate the signal generator. The output voltage
should read approximately 2V.
Layout Issues
The MAX2204 is not particularly sensitive to the layout,
since it only needs 5dBm for maximum output voltage.
However, there are two areas that need attention: the
GND pin and the supply bypassing. Connect the GND
pin to PCB ground with a GND via as close as possible,
and place the supply bypassing capacitor close to the
part.
MAX2204 Evaluation Kit
2
_______________________________________________________________________________________
Figure 1. MAX2204 EV Kit Schematic
U1
MAX2204
C4
2200pF
C2
27pF
C1
220pF
R2
0
VCC
VCC
3
2
JP1
1
1
2
3
4
5
J4
OUT
JP3
V
CC
GND
RFIN
ENA
OUT
VCC
C3
22
μ
F
J1
J2
R1
50
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2264 | 2.7V, Single-Supply, Cellular-Band Linear Power Amplifiers |
| MAX2264EUE | 2.7V, Single-Supply, Cellular-Band Linear Power Amplifiers |
| MAX2265EUE | 2.7V, Single-Supply, Cellular-Band Linear Power Amplifiers |
| MAX2266EUE | 2.7V, Single-Supply, Cellular-Band Linear Power Amplifiers |
| MAX2267 | +2.7V, Single-Supply, Cellular-Band Linear Power Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2204EVKIT+ | 功能描述:射頻開發工具 MAX2204 Eval Kit RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| MAX2204EXK | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:RF Power Detector |
| MAX2204EXK+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX2204EXK+T | 功能描述:射頻檢測器 RF Power Detector RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 頻率范圍:650 MHz to 3 GHz 最大二極管電容: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SC-88 封裝:Reel |
| MAX2204EXK+T10 | 功能描述:射頻檢測器 RF Power Detector RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 頻率范圍:650 MHz to 3 GHz 最大二極管電容: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SC-88 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。