- 您現在的位置：買賣IC網 > PDF目錄383345 > MAX218EWP (MAXIM INTEGRATED PRODUCTS INC) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | MAX218EWP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | LINE TRANSCEIVER, PDSO20 |
| 封裝： | SOP-20 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 92K |
| 代理商： | MAX218EWP |
M
1.8V to 4.25V-Powered,
True RS -232 Dual Transc eiver
_______________________________________________________________________________________
5
_______________Detailed Desc ription
The MAX218 line driver/receiver is intended for battery-
powered EIA/TIA-232 and V.28/V.24 communications
interfaces that require two drivers and two receivers.
The operating voltage extends from 1.8V to 4.25V, yet
the device maintains true RS-232 and EIA/TIA-562
transmitter output voltage levels. This wide supply volt-
age range permits direct operation from a variety of
batteries without the need for a voltage regulator. For
example, the MAX218 can be run directly from a single
lithium cell or a pair of alkaline cells. It can also be run
directly from two NiCd or NiMH cells from full-charge
voltage down to the normal 0.9V/cell end-of-life point.
The 4.25V maximum supply voltage allows the two
rechargeable cells to be trickle- or fast-charged while
driving the MAX218.
The circuit comprises three sections: power supply,
transmitters, and receivers. The power-supply section
converts the supplied input voltage to 6.5V, providing the
voltages necessary for the drivers to meet true RS-232
levels. External components are small and inexpensive.
The transmitters and receivers are guaranteed to oper-
ate at 120kbps data rates, providing compatibility with
LapLink and other high-speed communications soft-
ware. A shutdown mode extends battery life by reduc-
ing supply current to 0.04μA. While shut down, all
receivers can either remain active or be disabled under
logic control. With this feature, the MAX218 can be in
low-power shutdown mode and still monitor activity on
external devices. Three-state drivers are provided on
both receiver outputs.
S witc h-Mode Power S upply
The switch-mode power supply uses a single inductor
with one diode and three small capacitors to generate
±6.5V from an input voltage in the 1.8V to 4.25V
range.
Inductor Selection
Use a 15μH inductor with a saturation current rating of at
least 350mA and less than 1
resistance. Table 1 lists
suppliers of inductors that meet the 15μH/350mA/1
specifications.
Diode Selection
Key diode specifications are fast recovery time (<10ns),
average current rating (>100mA), and peak current rat-
ing (>350mA). Inexpensive fast silicon diodes, such as
the 1N6050, are generally recommended. More expen-
sive Schottky diodes improve efficiency and give slightly
better performance at very low V
voltages. Table 1
lists suppliers of both surface-mount and through-hole
diodes. 1N914s are usually satisfactory, but specifica-
tions and performance vary widely with different manu-
facturers.
Capacitor Selection
Use capacitors with values at least as indicated in
Figure 1. Capacitor C2 determines the ripple on V+,
but not the absolute voltage. Capacitors C1 and C3
determine both the ripple and the absolute voltage of
V-. Bypass V
CC
to GND with at least 1μF (C4) placed
close to pins 5 and 6. If the V
CC
line is not bypassed
elsewhere (e.g., at the power supply), increase C4 to
4.7μF.
You may use ceramic or polarized capacitors in all
locations. If you use polarized capacitors, tantalum
types are preferred because of the high operating fre-
quency of the power supplies (about 250kHz). If alu-
minum electrolytics are used, higher capacitance val-
ues may be required.
LapLink is a trademark of Traveling Software, Inc.
R1
R2
T1
T2
T1OUT
T2OUT
T1IN
T2IN
R1OUT
R2OUT
R1IN
R2IN
GND
EN
V
CC
SHDN
LX
C1+
C1-
V-
6
3
7
8
9
10
11
12
13
14
16
18
15
4
5, 17, 20
MAX218
ENABLE
ON/OFF
1.8V
TO
4.25V
1
V+
19
1
μ
F
C4
1
μ
F
C2
1
μ
F
C3
0.47
μ
F
C1
15
μ
H
D1
1N6050
Figure 1. Single-Supply Operation
相關PDF資料 |
PDF描述 |
|---|---|
| MAX218 | 16-Bit Buffers/Drivers With 3-State Outputs 48-SSOP -40 to 85 |
| MAX218CAP | 16-Bit Buffers/Drivers With 3-State Outputs 48-SSOP -40 to 85 |
| MAX218CPP | Replaced by SN74ABT16245A : 16-Bit Bus Transceivers With 3-State Outputs 48-TSSOP -40 to 85 |
| MAX218CWP | Replaced by SN74ABT16245A : 16-Bit Bus Transceivers With 3-State Outputs 48-SSOP -40 to 85 |
| MAX218EAP | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX218EWP+T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX218EWP-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX220 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:+5V-Powered, Multichannel RS-232 Drivers/Receivers |
| MAX220_10 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:5V-Powered, Multichannel RS-232 Drivers/Receivers |
| MAX2202EWT+T | 功能描述:射頻檢測器 RMS Power Detector RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 頻率范圍:650 MHz to 3 GHz 最大二極管電容: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SC-88 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。