參數資料
型號: MAX206E
廠商: Maxim Integrated Products, Inc.
英文描述: ±5kV ESD-Protected, +5V RS-232 Transceivers(5V,120kbps,自關閉方式, ESD保護,RS-232收發器)
中文描述: ±15kV ESD保護、+5V RS-232收發器
文件頁數: 10/24頁
文件大小: 265K
代理商: MAX206E
M
±15kV ESD-Protected, +5V RS-232 Transceivers
10
______________________________________________________________________________________
When in low-power shutdown mode, the MAX205E/
MAX206E/MAX211E/MAX213E/MAX241E driver outputs
are turned off and draw only leakage currents—even if
they are back-driven with voltages between 0V and
12V. Below -0.5V in shutdown, the transmitter output is
diode-clamped to ground with a 1k
series
impedance.
RS -232 Rec eivers
The receivers convert the RS-232 signals to CMOS-logic
output levels. The guaranteed 0.8V and 2.4V receiver
input thresholds are significantly tighter than the ±3V
thresholds required by the EIA/TIA-232E specification.
This allows the receiver inputs to respond to TTL/CMOS-
logic levels, as well as RS-232 levels.
The guaranteed 0.8V input low threshold ensures that
receivers shorted to ground have a logic 1 output. The
5k
input resistance to ground ensures that a receiver
with its input left open will also have a logic 1 output.
Receiver inputs have approximately 0.5V hysteresis.
This provides clean output transitions, even with slow
rise/fall-time signals with moderate amounts of noise
and ringing.
In shutdown, the MAX213E’s R4 and R5 receivers have
no hysteresis.
S hutdown and Enable Control
(MAX 205E/MAX 206E/MAX 211E/
MAX 213E/MAX 241E)
In shutdown mode, the charge pumps are turned off,
V+ is pulled down to V
CC
, V- is pulled to ground, and
the transmitter outputs are disabled. This reduces
supply current typically to 1μA (15μA for the MAX213E).
The time required to exit shutdown is under 1ms, as
shown in Figure 5.
Receivers
All MAX213E receivers, except R4 and R5, are put into
a high-impedance state in shutdown mode (see Tables
1a and 1b). The MAX213E’s R4 and R5 receivers still
function in shutdown mode. These two awake-in-
shutdown receivers can monitor external activity while
maintaining minimal power consumption.
The enable control is used to put the receiver outputs into
a high-impedance state, to allow wire-OR connection of
two EIA/TIA-232E ports (or ports of different types) at the
UART. It has no effect on the RS-232 drivers or the
charge pumps.
Note:
The enable control pin is active low for the
MAX211E/MAX241E (
EN
), but is active high for the
MAX213E (EN). The shutdown control pin is active high
for the MAX205E/MAX206E/MAX211E/MAX241E
(SHDN), but is active low for the MAX213E (
SHDN
).
C1-
I
L
-
R
L
-
V+
S1
V -
f
CLK
S2
S5
S6
C1
C3
C2
I
L
+
R
L
+
S3
S4
S7
S8
C4
C1+
GND
GND
V
CC
V
CC
C2-
C2+
PART
f
(kHz)
230
MAX202E
MAX203E
MAX205E–208E
MAX211E/213E
MAX232E
MAX241E
230
200
200
140
30
Figure 4. Charge-Pump Diagram
相關PDF資料
PDF描述
MAX211E ±5kV ESD-Protected, +5V RS-232 Transceivers(5V,120kbps,自關閉方式, ESD保護,RS-232收發器)
MAX232E ±5kV ESD-Protected, %2B5V RS-232 Transceivers
MAX203E ±5kV ESD-Protected, +5V RS-232 Transceivers(5V,120kbps,自關閉方式, ESD保護,RS-232收發器)
MAX2100 Quadrature Digitizer Circuits(正交數字轉換器電路)
MAX2102EVKIT-SO Evaluation Kit
相關代理商/技術參數
參數描述
MAX206EAG 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX206EAG+ 功能描述:RS-232接口集成電路 5V RS232 Transceiver w/0.1uF External Cap RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX206EAG+T 功能描述:RS-232接口集成電路 5V RS232 Transceiver w/0.1uF External Cap RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX206EAG-T 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX206ECAG 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: