- 您現在的位置：買賣IC網 > PDF目錄385523 > MAX2057EVKIT (Maxim Integrated Products, Inc.) Evaluation Kit PDF資料下載
參數資料
| 型號： | MAX2057EVKIT |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Evaluation Kit |
| 中文描述： | MAX2057評估板 |
| 文件頁數： | 2/6頁 |
| 文件大?。?/td> | 616K |
| 代理商： | MAX2057EVKIT |
E
Quick Start
The MAX2057 EV kit is fully assembled and factory tested.
Follow the instructions in the
Connections and Setup
section for proper device evaluation.
Test Equipment
One DC power supply capable of supplying 5V
and 0.3A
One DC power supply that can be adjusted from 1V
to 4.5V for gain control
Two digital multimeters (DMM) to monitor V
CC
and
I
CC
, if desired
HP 8648 (or equivalent) signal source
HP 8561E (or equivalent) spectrum analyzer
HP 8753D (or equivalent) network analyzer to mea-
sure return loss and gain over frequency (optional)
Connections and Setup
This section provides a step-by-step guide to testing the
basic functionality of the EV kit. To prevent damaging the
device,
do not turn on DC power or RF signal genera-
tors until all connections are made. Do not apply
VCNTL without V
CC
present (see the
VCNTL
section).
Testing the Supply Current
1) Connect 50
terminations to J1 and J2.
2) With its output disabled, set the voltage on one of
the DC supplies to +5.0V (through a low internal
resistance ammeter, if desired) and connect to the
+5.0V (TP1) and GND (TP2) terminals on the EV kit.
If the power supply has a current-limiting feature,
set the current limit to 250mA.
3) With its output disabled, set the voltage on the sec-
ond DC supply to 1V and connect to the gain-control
connector VCNTL (J3) on the EV kit. This configures
the device for its maximum gain setting. If the power
supply has a current-limiting feature, set the current
limit to 1mA.
4) Enable the V
CC
supply, then enable the gain-control
supply; the V
CC
supply current should read approxi-
mately 180mA.
Testing the Power Gain
1) With its supply output disabled, set the voltage on one
of the DC supplies to +5.0V (through a low internal
resistance ammeter, if desired) and connect to the
+5.0V (TP1) and GND (TP2) terminals on the EV kit. If
available, set the current limit to 250mA.
2) With its supply output disabled, set the voltage on the
other DC supply to 1V and connect to the gain-control
connector VCNTL (J3) on the EV kit. If available, set
the current limit to 1mA.
3) With the generator output disabled, connect the RF
signal generator to J1. Set the generator to a
2100MHz output frequency, and set the power level
to -12dBm.
4) Connect the spectrum analyzer to J2. Set the spec-
trum analyzer to a center frequency of 2100MHz
and a total span of 1MHz. Set the reference level on
the spectrum analyzer to +10dBm.
5) Enable the V
CC
supply. Next, enable the gain-control
supply. Finally, enable the RF generator’s output. A
2100MHz signal with a magnitude of approximately
3dBm should be displayed on the spectrum analyzer.
Be sure to account for external cable losses.
6) Vary the gain-control supply voltage between +1.0V
and +4.5V. The output power should vary by
approximately 21dB.
7) Gain can also be determined with a network analyzer.
This has the advantage of displaying gain over a
swept frequency band, in addition to displaying
input and output return loss. Refer to the network
analyzer manufacturer’s user manual for setup
details (optional).
Detailed Description
Figure 1 shows the schematic for the MAX2057 EV kit.
C1, C3, C5, and C7 are DC-blocking capacitors for the
IN_A, IN, AMP_IN, and OUT pins. To reduce the possi-
bility of noise pickup from the power supply, capacitors
C2, C4, C6, C8, C9, C10, C13, C14, and C15 are used
to decouple V
CC
. Resistors R1 and R2 are used to bias
the amplifier’s first and second stages, respectively.
Current-Setting Resistors
The MAX2057 amplifier section is a two-stage design
whose input stage current is set by the external resistor
R1, while the output stage current is set by resistor R2.
These resistors were optimized at the factory to pro-
duce the highest OIP3 for a given current. The current
of the device can be reduced by increasing these
resistor values (see the
Modifying the EV Kit
section),
but linearity performance degrades.
MAX2057 Evaluation Kit
2
_______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| MAX206E | ±5kV ESD-Protected, +5V RS-232 Transceivers(5V,120kbps,自關閉方式, ESD保護,RS-232收發器) |
| MAX211E | ±5kV ESD-Protected, +5V RS-232 Transceivers(5V,120kbps,自關閉方式, ESD保護,RS-232收發器) |
| MAX232E | ±5kV ESD-Protected, %2B5V RS-232 Transceivers |
| MAX203E | ±5kV ESD-Protected, +5V RS-232 Transceivers(5V,120kbps,自關閉方式, ESD保護,RS-232收發器) |
| MAX2100 | Quadrature Digitizer Circuits(正交數字轉換器電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2058 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:700MHz to 1200MHz High-Linearity, SPI-Controlled DVGA with Integrated Loopback Mixer |
| MAX2058ETL | 功能描述:射頻放大器 0.7GHz - 1.2GHz SPI-Controlled DVGA RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2058ETL+ | 功能描述:射頻放大器 0.7GHz - 1.2GHz SPI-Controlled DVGA RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2058ETL+T | 功能描述:射頻放大器 0.7GHz - 1.2GHz SPI-Controlled DVGA RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2058ETL-T | 功能描述:射頻放大器 0.7GHz - 1.2GHz SPI-Controlled DVGA RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。