- 您現在的位置：買賣IC網 > PDF目錄385523 > MAX2041EVKIT (Maxim Integrated Products, Inc.) Evaluation Kit PDF資料下載
參數資料
| 型號： | MAX2041EVKIT |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Evaluation Kit |
| 中文描述： | MAX2041評估板 |
| 文件頁數： | 2/7頁 |
| 文件大?。?/td> | 196K |
| 代理商： | MAX2041EVKIT |
E
MAX2041 Evaluation Kit
2
_______________________________________________________________________________________
Quick Start
The MAX2041 EV kit is fully assembled and factory test-
ed. Follow the instructions in the
Connections and
Setup
section for proper device evaluation.
Test Equipment Required
This section lists the recommended test equipment to
verify the operation of the MAX2041. It is intended as a
guide only, and substitutions may be possible:
DC supply capable of delivering +5.0V and 175mA
Three RF signal generators capable of delivering
10dBm of output power in the 1GHz to 3GHz frequency
range (i.e., HP 8648)
RF spectrum analyzer with a minimum 100kHz to
3GHz frequency range (HP 8561E)
RF power meter (HP 437B)
Power sensor (HP 8482A)
Connections and Setup
This section provides a step-by-step guide to testing
the basic functionality of the EV kit. As a general pre-
caution to prevent damaging the outputs by driving
high-VSWR loads, do not turn on DC power or RF signal
generators until all connections are made.
This procedure is specific to operation in the US PCS
band (reverse channel: 1850MHz to 1910MHz), high-
side injected LO for a 200MHz IF. Choose the test fre-
quency based on the particular system’s frequency
plan, and adjust the following procedure accordingly.
See Figure 1 for the mixer test setup diagram:
1) Calibrate the power meter for 2100MHz. For safety
margin, use a power sensor rated to at least
+20dBm, or use padding to protect the power head
as necessary.
2) Connect 3dB pads to DUT ends of each of the two
RF signal generators’ SMA cables. This padding
improves VSWR and reduces the errors due to mis-
match.
3) Use the power meter to set the RF signal generators
according to the following:
RF signal source: 0dBm into DUT at 1900MHz
(this will be about +3dBm before the 3dB pad).
LO1 signal source: 0dBm into DUT at 2100MHz
(this will be about +3dBm before the 3dB pad).
LO2 signal source: 0dBm into DUT at 2101MHz
(this will be about +3dBm before the 3dB pad).
4) Disable the signal generator outputs.
5) Connect the RF source (with pad) to the RF port.
6) Connect the LO1 and LO2 signal sources to the EV
kit’s LO1 and LO2 inputs, respectively.
7) Measure the loss in the 3dB pad and cable that will
be connected to the IF port. Losses are frequency
dependent, so test this at 200MHz (the IF frequency).
Use this loss as an offset in all output power/
gain calculations.
8) Connect this 3dB pad to the EV kit’s IF port connec-
tor and connect a cable from the pad to the spec-
trum analyzer.
9) Set the DC supply to +5.0V, and set a current limit
of around 175mA if possible. Disable the output
voltage and connect the supply to the EV kit
(through an ammeter, if desired). Enable the sup-
ply. Readjust the supply to get +5.0V at the EV kit.
There will be a voltage drop across the ammeter
when the mixer is drawing current.
10) Select LO1 by connecting LOSEL (TP3) to GND.
11) Enable the LO and the RF sources.
Testing the Mixer
Adjust the center and span of the spectrum analyzer to
observe the IF output tone at 200MHz. The level should
be about -10.2dBm (7.2dB conversion loss, 3dB pad
loss). The spectrum analyzer’s absolute magnitude
accuracy is typically no better than ±1dB. Use the power
meter to get an accurate output power measurement.
Disconnect the GND connection to LOSEL. It will be
pulled high by a pullup resistor on the board to select
LO2. Observe that the 201MHz signal increases while
the 200MHz decreases.
Reconfigure the test setup using a combiner or hybrid
to sum the two LO inputs to do a two-tone IP3 measure-
ment if desired. Terminate the unused LO input in 50
Ω
.
Component List (continued)
DESIGNATION
QTY
DESCRIPTION
U1
1
Mixer IC (5mm x 5mm 20-pin QFN
EP)
Maxim MAX2041ETP+
NOTE: U1 HAS AN EXPOSED
PADDLE CONDUCTOR THAT
REQUIRES IT TO BE SOLDER
ATTACHED TO A GROUNDED PAD
ON THE CIRCUIT BOARD TO
ENSURE A PROPER
ELECTRICAL/THERMAL DESIGN.
+
Denotes lead-free package.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2041 | High-Linearity, 1700MHz to 3000MHz Upconversion / Downconversion Mixer with LO Buffer / Switch |
| MAX2041ETP | High-Linearity, 1700MHz to 3000MHz Upconversion / Downconversion Mixer with LO Buffer / Switch |
| MAX2041ETP-T | High-Linearity, 1700MHz to 3000MHz Upconversion / Downconversion Mixer with LO Buffer / Switch |
| MAX2043 | Evaluation Kit |
| MAX2043_1 | Evaluation Kit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2042 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SiGe High-Linearity, 2000MHz to 3000MHz Upconversion/Downconversion Mixer with LO Buffer |
| MAX2042A | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SiGe High-Linearity, 1600MHz to 3900MHz Upconversion/Downconversion |
| MAX2042AETP | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SiGe High-Linearity, 1600MHz to 3900MHz Upconversion/Downconversion |
| MAX2042AETP+ | 功能描述:射頻混合器 1.6-3.9GHz Up/Down Conversion Mixer RoHS:否 制造商:NXP Semiconductors 頻率范圍: 轉換損失——最大: 工作電源電壓:6 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| MAX2042AETP+T | 功能描述:射頻混合器 1.6-3.9GHz Up/Down Conversion Mixer RoHS:否 制造商:NXP Semiconductors 頻率范圍: 轉換損失——最大: 工作電源電壓:6 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。