- 您現在的位置：買賣IC網 > PDF目錄384655 > MAX2003CSE (MAXIM INTEGRATED PRODUCTS INC) NiCd/NiMH Battery Fast-Charge Controllers PDF資料下載
參數資料
| 型號： | MAX2003CSE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | NiCd/NiMH Battery Fast-Charge Controllers |
| 中文描述： | BATTERY CHARGE CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 0.150 INCH, SOIC-16 |
| 文件頁數： | 4/20頁 |
| 文件大小： | 211K |
| 代理商： | MAX2003CSE |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
M
NiCd/NiMH Battery
Fast-Charge Controllers
4
_______________________________________________________________________________________
______________________________________________________________Pin Desc ription
NAME
FUNCTION
1
CCMD
Charge-Enabled Mode Input—initiates fast-charge on a digital signal (see Detailed Descriptionfor operating
conditions).
2
DCMD
Discharge-Enable Mode Input—initiates discharge-before-charge on a digital signal (see Detailed
Descriptionfor operating conditions).
PIN
3
DVEN
Negative Delta Voltage (-
V) Enable Input—enables -
V charge-termination mode. If DVEN is high, the con-
troller uses negative-voltage change detection to terminate charge. If DVEN is low, this mode is disabled.
4, 5
TM1,
TM2
These inputs are used to program the fast-charge and hold-off times, and to enable the top-off charge
mode. The inputs can be high, low, or floating. See Table 4 for details.
9
SNS
Current-Sense Input—connected to the negative battery terminal. TS and BAT are referenced to this pin.
The voltage at SNS is directly proportional to the current through the battery and is used to determine how
and when MOD switches.
8
V
SS
Ground
7
BAT
Input Voltage of Single Battery Cell. If more than one cell is present, a resistor divider is needed to divide the
voltage down to a single cell voltage.
6
TS
Temperature Sense-Voltage Input from external thermistor. The thermistor temperature coefficient is nega-
tive, so the higher the temperature, the lower the voltage at this pin (See Detailed Descriptionfor conditions
of operation).
14
MOD
Modulation Output. This push/pull output switches to enable or disable charging current. If MOD is high,
current is enabled. If it is low, current is disabled. For a 5V supply, if the voltage at the SNS pin is less than
220mV, MOD is high. If the voltage is above 250mV, MOD is low.
13
CHG
Charge Status Output. This push/pull LED driver indicates charge status (see Detailed Description.
12
TEMP
Temperature Status Output. This push/pull LED driver indicates that the temperature is outside the accept-
able limits, and fast-charge and top-off are inhibited (see Maximum Temperature Terminationsection in
Detailed Description.
11
MCV
Maximum Cell Voltage Input. If the voltage from BAT to SNS exceeds the voltage at MCV, fast or top-off
charging is terminated.
10
TCO
Temperature Cutoff-Voltage Input. If the voltage from TS to SNS is less than the voltage at TCO, a hot ther-
mistor (negative coefficient) is detected and fast or top-off charging is terminated.
16
V
CC
Power-Supply Voltage Input (+5V nominal). Bypass with a 0.1μF capacitor placed close to the device.
15
DIS
Discharge-Switch Control Output. This push/pull output turns on the FET that discharges the battery.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2003CWE | NiCd/NiMH Battery Fast-Charge Controllers |
| MAX2009ETI-T | 1200MHz to 2500MHz Adjustable RF Predistorter |
| MAX2009 | 1200MHz to 2500MHz Adjustable RF Predistorter |
| MAX2016 | LF-to-2.5GHz Dual Logarithmic Detector/ Controller for Power, Gain, and VSWR Measurements |
| MAX2016ETI | LF-to-2.5GHz Dual Logarithmic Detector/ Controller for Power, Gain, and VSWR Measurements |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2003CWE | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX2003CWE-T | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX20050ATC/V+T | 制造商:Maxim Integrated Products 功能描述:2A SYNCHRONOUS BUCK LED DRIVER WITH INTEGRATED MOSFETS - Tape and Reel |
| MAX20050AUD/V+T | 制造商:Maxim Integrated Products 功能描述:2A SYNCHRONOUS BUCK LED DRIVER WITH INTEGRATED MOSFETS - Tape and Reel |
| MAX20051ATC/V+T | 制造商:Maxim Integrated Products 功能描述:2A SYNCHRONOUS BUCK LED DRIVER WITH INTEGRATED MOSFETS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。