- 您現在的位置：買賣IC網 > PDF目錄384655 > MAX1965 (Maxim Integrated Products, Inc.) Tracking/Sequencing Triple/Quintuple Power-Supply Controllers PDF資料下載
參數資料
| 型號： | MAX1965 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Tracking/Sequencing Triple/Quintuple Power-Supply Controllers |
| 中文描述： | 三/五路電源控制器，提供跟蹤/排序功能 |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 475K |
| 代理商： | MAX1965 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
The DL low-side drive waveform is always the comple-
ment of the DH high-side drive waveform (with con-
trolled dead time to prevent cross-conduction or
“
shoot-through
”
). A dead-time circuit monitors the DL
output and prevents the high-side FET from turning on
until DL is fully off. In order for the dead-time circuit to
work properly, there must be a low-resistance, low-
inductance path from the DL driver to the MOSFET
gate. Otherwise, the sense circuitry in the MAX1964/
MAX1965 will interpret the MOSFET gate as
“
off
”
when
gate charge actually remains. Use very short, wide
traces (50mils to 100mils wide if the MOSFET is 1 inch
from the device). The dead time at the other edge (DH
turning off) is determined by a fixed internal delay.
High-Side Gate-Drive Supply (BST)
Gate-drive voltage for the high-side N-channel switch is
generated by a flying-capacitor boost circuit (Figure 1).
The capacitor between BST and LX is alternately
charged from the VL supply and placed parallel to the
high-side MOSFET
’
s gate and source terminals.
On startup, the synchronous rectifier (low-side MOS-
FET) forces LX to ground and charges the boost
capacitor to 5V. On the second half-cycle, the switch-
mode power supply turns on the high-side MOSFET by
closing an internal switch between BST and DH. This
provides the necessary gate-to-source voltage to turn
on the high-side switch, an action that boosts the 5V
gate-drive signal above the input voltage.
Internal 5V Linear Regulator (VL)
All MAX1964/MAX1965 functions, except the current-
sense amplifier, are internally powered from the on-
chip, low-dropout 5V regulator. The maximum regulator
input voltage (V
IN
) is 28V. Bypass the regulator
’
s output
(VL) with a ceramic capacitor of at least 1μF to GND.
The V
IN
-to-VL dropout voltage is typically 200mV, so
when V
IN
is less than 5.2V, VL is typically V
IN
- 200mV.
The internal linear regulator can source up to 20mA to
supply the IC, power the low-side gate driver, charge
the external boost capacitor, and supply small external
loads. When driving particularly large FETs, little or no
regulator current may be available for external loads.
For example, when switched at 200kHz, a large FET
with 40nC total gate charge requires 40nC x 200kHz, or
8mA.
Undervoltage Lockout
If VL drops below 3.5V, the MAX1964/MAX1965
assumes that the supply voltage is too low to make
valid decisions, so the undervoltage lockout (UVLO)
circuitry inhibits switching, forces POK low, and forces
the DL and DH gate drivers low. After VL rises above
3.5V, the controller powers up the outputs (see
Startup
section).
Startup
Externally, the MAX1964/MAX1965 start switching when
VL rises above the 3.5V undervoltage lockout thresh-
old. However, the controller is not enabled unless
all
four
conditions are met: 1) VL exceeds the 3.5V under-
voltage lockout threshold, 2) the internal reference
exceeds 92% of its nominal value (V
REF
> 1.145V), 3)
the internal bias circuitry powers up, and 4) the thermal
limit is not exceeded. Once the MAX1964/MAX1965
assert the internal enable signal, the step-down con-
troller starts switching and enables soft-start.
The soft-start circuitry gradually ramps up to the refer-
ence voltage in order to control the rate of rise of the
step-down controller and reduce input surge currents
M
Tracking/Sequencing Triple/Quintuple
Power-Supply Controllers
______________________________________________________________________________________
15
Figure 3.
“
Valley
”
Current-Limit Threshold Point
I
I
VALLEY
I
LOAD
[
(
)
]
TIME
-I
PEAK
L
V
OUT
V
IN
OSC
(V
IN
- V
OUT
)
I
PEAK
= I
VALLEY
+
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1964TEEE | Tracking/Sequencing Triple/Quintuple Power-Supply Controllers |
| MAX1965TEEP | Tracking/Sequencing Triple/Quintuple Power-Supply Controllers |
| MAX1966 | Low-Cost Voltage-Mode PWM Step-Down Controllers |
| MAX1967EUB | Low-Cost Voltage-Mode PWM Step-Down Controllers |
| MAX1966-MAX1967 | Low-Cost Voltage-Mode PWM Step-Down Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1965TEEP | 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX1965TEEP-T | 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX1966ESA | 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX1966ESA+ | 功能描述:電壓模式 PWM 控制器 Voltage-Mode PWM Step-Down RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX1966ESA+T | 功能描述:電壓模式 PWM 控制器 Voltage-Mode PWM Step-Down RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。