- 您現在的位置：買賣IC網 > PDF目錄384654 > MAX1889EGE (MAXIM INTEGRATED PRODUCTS INC) Triple-Output TFT LCD Power Supply with Fault Protection PDF資料下載
參數資料
| 型號： | MAX1889EGE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Triple-Output TFT LCD Power Supply with Fault Protection |
| 中文描述： | 2.8 A SWITCHING REGULATOR, 1250 kHz SWITCHING FREQ-MAX, QCC16 |
| 封裝： | 5 X 5 MM, 0.90 MM HEIGHT, THIN, QFN-16 |
| 文件頁數： | 18/32頁 |
| 文件大?。?/td> | 796K |
| 代理商： | MAX1889EGE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
Triple-Output TFT LCD Power Supply
with Fault Protection
18
______________________________________________________________________________________
Therefore, the dominant pole and the RHP zero deter-
mine the loop response of the step-up regulator. The fre-
quency of the dominant pole is:
where R
L
is the load resistance and C is the output
capacitor. The frequency of the RHP zero is:
where D is the duty cycle, L is the inductance, and the
DC gain is given by:
where R
CS
is the internal current-sense resistor, and R1
and R2 are the feedback divider resistors in Figure 5.
However, adding lead or lag compensation (Figure 5)
can be useful to adjust the trade-off between stability
and transient response. If greater phase margin is need-
ed for stability, and lower bandwidth is acceptable, add
a pole-zero pair by connecting an RC network from the
FB pin to ground (lag compensation). Conversely, if
higher bandwidth is required for faster transient
response, and lower phase margin is acceptable, add a
zero-pole pair to the loop by connecting an RC network
from the FB pin to the main output (lead compensation).
The frequencies of the pole and zero for the lag com-
pensation are:
The frequencies of the zero and pole for the lead com-
pensation are:
The compensation resistors R3 and R4 change the AC
gain affecting the loop bandwidth and phase margin at
crossover. Reducing the bandwidth too much (FB com-
pensation) harms the transient response, while increas-
ing it too much harms phase margin and stability. As a
rule, start with R3 (or R4) approximately equal to half of
R1 (or R2). In a typical application, the compensation
capacitors C1 and C2 can be in the range between
100pF to 1000pF. Then, check the stability by monitoring
the transient response waveform when a pulsed load is
applied to the output.
Using Compensation for Improved Soft-Start
The digital soft-start of the main step-up regulator limits
the average input current during startup. In order to
smooth out each step of the digital soft-start, add a low-
frequency lead compensation network (Figure 5). The
network effectively spreads out the switching pulses
and lowers the peak inductor currents.
The smoothing network is active only during soft-start
when the output voltage rises. Positive changes in the
output are instantaneously coupled to the FB pin
through D1 and feed-forward capacitor C2. This
arrangement generates a smoothly rising output volt-
age. When the output voltage reaches regulation, C2
charges up through R3 and D1 turns off. In most appli-
cations, the lead compensation is not needed and can
be disabled by making R3 large. With R3 > R2, the
pole and the zero in the compensation network are very
close to one another and cancel out.
f
R
(
R
C
f
R
R
R
R
R
C
Z FF
_
P FF
_
=
+
)
×
=
+
×
+
1
2
2
3
2
1
2
3
1
1
2
2
2
π
π
f
R
R
R
R
R
C
f
R
C
P FB
_
Z FB
_
=
×
+
=
×
1
2
4
1
1
2
2
1
1
4
2
1
π
π
A
R
+
R
R
D
R
R
DC
CS
L
=
×
×
20
1
1
2
1
(
log
)
f
D
R
2
L
Z RHP
_
L
=
(
)
1
2
-
π
f
R C
P DOMINANT
_
=
1
2
π
MAX1889
V
IN
L
D
V
MAIN
R
L
C
C2
C1
R1
R2
R3
R4
LX
FB
GND
PGND
D1
Figure 5. External Compensation
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1889ETE | Triple-Output TFT LCD Power Supply with Fault Protection |
| MAX1889 | Fixed-Point Digital Signal Processor 256-BGA |
| MAX1896 | 1.4MHz SOT23 Current-Mode Step-Up DC-DC Converter |
| MAX1896EUT-T | Fixed-Point Digital Signal Processor 532-FCBGA |
| MAX1898 | Fixed-Point Digital Signal Processor 532-FCBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1889EGE+ | 制造商:Maxim Integrated Products 功能描述:TRIPLE-OUTPUT TFT LCD POWER SUPPLY WITH FAULT PROTECTION - Rail/Tube |
| MAX1889ETE | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX1889ETE+ | 功能描述:直流/直流開關轉換器 Quad-Output TFT LCD Power Supply RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1889ETE+T | 功能描述:LCD 驅動器 Quad-Output TFT LCD Power Supply RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX1889ETE-T | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。