- 您現在的位置：買賣IC網 > PDF目錄384654 > MAX1865TEEP (MAXIM INTEGRATED PRODUCTS INC) xDSL/Cable Modem Triple/Quintuple Output Power Supplies PDF資料下載
參數資料
| 型號： | MAX1865TEEP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | xDSL/Cable Modem Triple/Quintuple Output Power Supplies |
| 中文描述： | 0.5 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, QSOP-20 |
| 文件頁數： | 21/25頁 |
| 文件大?。?/td> | 384K |
| 代理商： | MAX1865TEEP |
M
xDSL/Cable Modem Triple/Quintuple Output
Power Supplies
______________________________________________________________________________________
21
Do not use output capacitors with more than 200m
of
ESR. Typically, more output capacitance provides the
best solution, since this also reduces the output voltage
drop immediately after a load transient.
Linear Regulator Output Capacitors
Connect at least a 1μF capacitor between the linear
regulator
’
s output and ground, as close to the
MAX1864/MAX1865 and external pass transistors as
possible. Depending on the selected pass transistor,
larger capacitor values may be required for stability
(see
Stability Requirements
). Furthermore, the output
capacitor
’
s ESR affects stability, providing a zero that
may be necessary to cancel the second pole. Use out-
put capacitors with an ESR less than 200m
to ensure
stability and optimum transient response.
Once the minimum capacitor value for stability is deter-
mined, verify that the linear regulator
’
s output does not
contain excessive noise. Although adequate for stabili-
ty, small capacitor values may provide too much band-
width, making the linear regulator sensitive to noise.
Larger capacitor values reduce the bandwidth, thereby
reducing the regulator
’
s noise sensitivity.
If noise on the ground reference causes the design to
be marginally stable for the negative linear regulator,
bypass the negative output back to its reference volt-
age (V
REF
, Figure 7). This technique reduces the differ-
ential noise on the output.
Base-Drive Noise Reduction
The high-impedance base driver is susceptible to sys-
tem noise, especially when the linear regulator is lightly
loaded. Capacitively coupled switching noise or induc-
tively coupled EMI onto the base drive causes fluctua-
tions in the base current, which appear as noise on the
linear regulator
’
s output. Keep the base-drive traces
away from the step-down converter and as short as
possible to minimize noise coupling. Resistors in series
with the gate drivers (DH and DL) reduce the LX
switching noise generated by the step-down converter
(Figure 5). Additionally, a bypass capacitor may be
placed across the base-to-emitter resistor (Figure 7).
This bypass capacitor, in addition to the transistor
’
s
input capacitance, could bring in a second pole that
will destabilize the linear regulator (see
Stability
Requirements
). Therefore, the stability requirements
determine the maximum base-to-emitter capacitance:
where C
IN(Q)
is the transistor
’
s input capacitance, and
f
POLE(CBE)
is the second pole required for stability.
Transformer Selection
In systems where the step-down controller
’
s output is
not the highest voltage, a transformer may be used to
provide additional postregulated, high-voltage outputs.
The transformer generates unregulated, high-voltage
supplies that power the positive and negative linear
regulators. These unregulated supply voltages must be
high enough to keep the pass transistors from saturat-
ing. For positive output voltages, connect the trans-
former as shown in figure 6 where the minimum turns
ratio (N) is determined by:
where V
SAT
is the pass transistor
’
s saturation voltage
under full load. For negative output voltages (MAX1865
N
V
V
V
V
POS
LDO POS
(
SAT
DIODE
OUT
≥
+
+
)
-1
C
R
R
V h
C
BE
POLE CBE
BELOAD
BE T FE
I( )
≤
+
1
2
π
(
)
-
≈
POLE FB
OUT ESR
C
(
)
1
2
π
C
BYP
V
NEG
V
SUP
Q
PASS
C
LDO
R
BE
C
BE
R1
R2
B_
a) POSITIVE OUTPUT VOLTAGE
b) NEGATIVE OUTPUT VOLTAGE (MAX1865 ONLY)
FB_
MAX1864
MAX1865
V
POS
C
BYP
V
REF
V
SUP
Q
PASS
C
NEG
R
BE
C
BE
R4
R3
BF5
B5
MAX1865
Figure 7. Base-Drive Noise Reduction
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1864TEEE | xDSL/Cable Modem Triple/Quintuple Output Power Supplies |
| MAX1887 | Quick-PWM Slave Controllers for Multiphase, Step-Down |
| MAX1889EGE | Triple-Output TFT LCD Power Supply with Fault Protection |
| MAX1889ETE | Triple-Output TFT LCD Power Supply with Fault Protection |
| MAX1889 | Fixed-Point Digital Signal Processor 256-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1865TEEP+ | 功能描述:DC/DC 開關控制器 xDSL/Cable Modem Triple/Quint Output RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1865TEEP+T | 功能描述:電流和電力監控器、調節器 xDSL/Cable Modem Triple/Quint Output RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX1865TEEP-T | 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX1865UEEP | 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| MAX1865UEEP-T | 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。