參數資料
型號: MAX1812
廠商: Maxim Integrated Products, Inc.
英文描述: Dual USB Switch with Fault Blanking
中文描述: 雙路、USB開關,帶有故障屏蔽
文件頁數: 6/10頁
文件大?。?/td> 296K
代理商: MAX1812
M
Detailed Description
The MAX1812 is a dual current-limited switch designed
specifically for USB applications. It has two indepen-
dent switches, each with its own enable control input.
Each switch also has an independent error flag output
to notify the USB controller when the current-limit, short-
circuit, undervoltage-lockout, or thermal-shutdown
threshold is reached (Figure 1).
The MAX1812 operates from a +4V to +5.5V input volt-
age and guarantees a minimum output current of
500mA. A built-in current-limit of 0.9A (typ) limits the
current in the event of a heavy overload condition. The
MAX1812 has independent thermal shutdown for each
switch in the event of a prolonged overload or short-cir-
cuit condition.
Use of internal low R
ON
NMOS switches enables the
MAX1812 to fit two switches in the ultra-small 10-pin
μMAX package. An internal micropower charge pump
generates the high-side supply needed for driving the
gates of these high-side switches. Separate current-
limiting and thermal-shutdown circuits permit each
switch to operate independently, improving system
robustness.
Undervoltage Lockout and
Input Voltage Requirements
The MAX1812 includes an undervoltage-lockout
(UVLO) circuit to prevent erroneous switch operation
when the input voltage goes low during startups and
brownout conditions. Operation is inhibited when V
IN_
< 3.4V.
Output Fault Protection
The MAX1812 senses the switch output voltage and
selects continuous current limiting when V
OUT
_ > 1V, or
pulsed current limiting when V
OUT_
< 1V. When V
OUT_
> 1V, the device operates in a continuous current-limit
mode, which sets the output current limit to 0.9A (typ).
When V
OUT_
< 1V, the device operates in short-circuit
current-limit mode. The MAX1812 pulses the output
current at 400Hz to limit the output current to 0.35A
(RMS).
Thermal Shutdown
The MAX1812 features independent thermal shutdown
for each switch channel, allowing one switch to deliver
power even if the other switch has a fault condition.
When the junction temperature exceeds +160
°
C, the
switch turns off and the
FAULT_
output goes low imme-
diately; fault blanking does not occur during thermal
limit. When the junction cools by 15
°
C, the switch turns
back on again. If the fault overload condition continues,
the switch will cycle on and off, resulting in a pulsed
output that saves battery power.
Fault Indicators
The MAX1812 provides an open-drain fault output
(
FAULT_
)
for each switch. For most applications, con-
nect
FAULT_
to IN_ through a 100k
pullup resistor.
Dual USB Switch with Fault Blanking
6
_______________________________________________________________________________________
PIN
NAME
FUNCTION
1
ONA
Control Input for Switch A. Can be driven higher than IN_ without damage. A logic low turns switch A
on.
2, 3, 4
INA, IN,
INB
Power Input. Connect all IN_ pins together and bypass with a 0.1
μ
F capacitor to ground. Load
conditions may require additional bulk capacitance to prevent the input from being pulled down.
5
ONB
Control Input for Switch B. Can be higher than IN_ without damage. A logic low turns switch B on.
6
FAULTB
Fault Indicator Output for Switch B. This open-drain output goes low when switch B is in thermal
shutdown or undervoltage lockout or in a sustained (>20ms) current-limit or short-circuit condition.
7
OUTB
Power Output for Switch B. Connect a 1
μ
F capacitor from OUTB to ground. Load condition may
require additional bulk capacitance. See USB requirements.
8
GND
Ground
9
OUTA
Power Output for Switch A. Connect a 1
μ
F capacitor from OUTA to ground. Load condition may
require additional bulk capacitance. See USB requirements.
10
FAULTA
Fault Indicator Output for Switch A. This open-drain output goes low when switch A is in thermal
shutdown or undervoltage lockout or in a sustained (>20ms) current-limit or short-circuit condition.
Pin Description
相關PDF資料
PDF描述
MAX1812EUB Dual USB Switch with Fault Blanking
MAX1817 Replaced by TMS320VC5506 : Digital Signal Processors 132-BQFP
MAX1817EUB Replaced by TMS320VC5506 : Digital Signal Processors 132-BQFP -40 to 85
MAX1822 High-Side Power Supply
MAX1822ESA High-Side Power Supply
相關代理商/技術參數
參數描述
MAX1812EUB 功能描述:電源開關 IC - USB Dual USB Switch w/Fault Blanking RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1812EUB+ 功能描述:電源開關 IC - USB Dual USB Switch w/Fault Blanking RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1812EUB+T 功能描述:電源開關 IC - USB Dual USB Switch w/Fault Blanking RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1812EUB-T 功能描述:電源開關 IC - USB Dual USB Switch w/Fault Blanking RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1813EEI 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK