- 您現在的位置：買賣IC網 > PDF目錄383335 > MAX1792 (Maxim Integrated Products, Inc.) 500mA Low-Dropout Linear Regulator in レMAX PDF資料下載
參數資料
| 型號： | MAX1792 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 500mA Low-Dropout Linear Regulator in レMAX |
| 中文描述： | 500mA、低壓差線性穩壓器，µMAX封裝 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 414K |
| 代理商： | MAX1792 |
M
The MAX1792 does not suffer from these problems and
consumes only 110μA of quiescent current under
heavy loads as well as in dropout.
Output Voltage Selection
The MAX1792
’
s Dual Mode operation allows operation
in either a preset voltage mode or an adjustable mode.
Connect SET to GND to select the preset output volt-
age. The two-digit part number suffix identifies the out-
put voltage (see
Selector Guide
). For example, the
MAX1792EUA33 has a preset 3.3V output voltage.
The output voltage may also be adjusted by connecting
a voltage-divider from OUT to SET to GND (Figure 2).
Select R2 in the 25k
to 100k
range. Calculate R1
with the following equation:
R1 = R2 [(V
OUT
/ V
SET
) - 1]
where V
SET
= 1.25V and V
OUT
may range from 1.25V to
5.0V.
Shutdown
Pull
SHDN
low to enter shutdown. During shutdown, the
output is disconnected from the input and supply current
drops to 0.1μA. When in shutdown,
RST
pulls low and
OUT is discharged through an internal 5k
resistor. The
capacitance and load at OUT determine the rate at
which V
OUT
decays.
SHDN
can be pulled as high as
+6V, regardless of the input and output voltage.
Reset Output
The reset output (
RST
) pulls low when OUT is less than
93% of the nominal regulation voltage. Once OUT
exceeds 93% of the nominal voltage,
RST
goes high
impedance after 4ms.
RST
is an open-drain N-channel
output. To obtain a voltage output, connect a pullup
resistor from
RST
to OUT. A 100k
resistor works well for
most applications.
RST
can be used as a power-on-reset
(POR) signal to a microcontroller (μC), or drive an exter-
nal LED to indicate power failure. When the MAX1792 is
shut down,
RST
is held low independent of the output
voltage. If unused, leave
RST
grounded or unconnected.
Current Limit
The MAX1792 monitors and controls the pass transis-
tor
’
s gate voltage, limiting the output current to 0.8A
(typ). This current limit doubles when the output voltage
is within 4% of the nominal value to improve perfor-
mance with large load transients. The output can be
shorted to ground for an indefinite period of time with-
out damaging the part.
Thermal Overload Protection
Thermal overload protection limits total power dissipa-
tion in the MAX1792. When the junction temperature
exceeds T
J
= +170
°
C, a thermal sensor turns off the
pass transistor, allowing the device to cool. The thermal
sensor turns the pass transistor on again after the junc-
tion temperature cools by 20
°
C, resulting in a pulsed
output during continuous thermal overload conditions.
Thermal overload protection protects the MAX1792 in
the event of fault conditions. For continuous operation,
do not exceed the absolute maximum junction-temper-
ature rating of T
J
= +150
°
C.
Operating Region and
Power Dissipation
The MAX1792
’
s maximum power dissipation depends on
the thermal resistance of the IC package and circuit
board, the temperature difference between the die junc-
tion and ambient air, and the rate of air flow. The power
dissipated in the device is P = I
OUT
x (V
IN
- V
OUT
). The
maximum allowed power dissipation is 1.3W or:
P
MAX
= (T
J(MAX)
- T
A
) / (
θ
JC
+
θ
CA
)
where T
J
- T
A
is the temperature difference between
the MAX1792 die junction and the surrounding air,
θ
JC
is the thermal resistance from the junction to the case,
and
θ
CA
is the thermal resistance from the case
through the PC board, copper traces, and other materi-
als to the surrounding air.
The MAX1792 package features an exposed thermal
pad on its underside. This pad lowers the thermal resis-
tance of the package by providing a direct heat con-
500mA Low-Dropout
Linear Regulator in μMAX
8
_______________________________________________________________________________________
OUT
OUT
SET
GND
IN
IN
SHDN
RST
C
OUT
3.3
μ
F
V
OUT
V
OUT
1.25V
C
IN
1
μ
F
ON
OFF
V
IN
= +2.5V TO +5.5V
R
2
R1 = R2
- 1
MAX1792
R
1
Figure 2. Adjustable Output Using External Feedback
Resistors
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1792EUA15 | 500mA Low-Dropout Linear Regulator in レMAX |
| MAX1792EUA18 | 500mA Low-Dropout Linear Regulator in レMAX |
| MAX1792EUA25 | 500mA Low-Dropout Linear Regulator in レMAX |
| MAX1792EUA33 | Replaced by TMS320C6722B : Digital Signal Processor 181-CPGA |
| MAX1792EUA__ | Replaced by TMS320VC33 : Digital Signal Processor 132-BQFP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1792EUA15 | 功能描述:低壓差穩壓器 - LDO 500mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX1792EUA15+ | 功能描述:低壓差穩壓器 - LDO 500mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX1792EUA15+T | 功能描述:低壓差穩壓器 - LDO 500mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX1792EUA15-T | 功能描述:低壓差穩壓器 - LDO 500mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX1792EUA15-TG069 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。