- 您現在的位置：買賣IC網 > PDF目錄384654 > MAX1763EUE (MAXIM INTEGRATED PRODUCTS INC) Replaced by TMS320C6410 : Digital Signal Processors 68-PLCC -40 to 85 PDF資料下載
參數資料
| 型號： | MAX1763EUE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Replaced by TMS320C6410 : Digital Signal Processors 68-PLCC -40 to 85 |
| 中文描述： | 3.4 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 4.40 MM, EXPOSED PAD, TSSOP-16 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 456K |
| 代理商： | MAX1763EUE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
M
Detailed Description
The MAX1763 is a highly-efficient, low-noise power
supply for portable RF and hand-held instruments. It
combines a boost switching regulator, N-channel
power MOSFET, P-channel synchronous rectifier, preci-
sion reference, shutdown control, and a versatile gain
block (Figure 1).
The DC-DC converter boosts a one-cell to three-cell
battery voltage input to a fixed 3.3V or adjustable volt-
age between 2.5V and 5.5V. An external Schottky
diode is required for output voltages greater than 4V.
The MAX1763 guarantees startup with an input voltage
as low as 1.1V and remains operational down to an
input of just 0.7V. It is optimized for use in cellular
phones and other applications requiring low noise and
low quiescent current for maximum battery life. It fea-
tures constant-frequency (1MHz), low-noise PWM oper-
ation with up to 1.5A output capability. A CLK input
allows frequency synchronization to control the output
1.5A, Low-Noise, 1MHz, Step-Up
DC-DC Converter
8
_______________________________________________________________________________________
Pin Description
PIN
NAME
FUNCTION
1
ONA
On Control Input. When ONA = high or
ONB
= low, the IC turns on. Connect ONA to OUT for normal
operation (Table 3).
2
ISET
N-Channel Current Limit Control. For maximum current limit, connect to REF. To reduce current,
supply a voltage between REF and GND by means of a resistive voltage-divider. If soft-start is
desired, connect a capacitor from ISET to GND. When ONA = low and
ONB
= high, or V
REF
< 80% of
nominal value, an on-chip switched resistor (100k
typ) discharges this pin to GND.
1.250V Voltage Reference Bypass Pin. Connect a 0.22μF ceramic bypass capacitor to GND. Up to
50μA of external REF load current is allowed.
3
REF
4
GND
Ground. Connect to PGND with short trace.
5
FB
DC-DC Converter Feedback Input. To set fixed output voltage of +3.3V, connect FB to ground. For
adjustable output of 2.5V to 5.5V, connect to a resistive divider placed from OUT to GND. FB set
point is 1.245V (Figure 6).
IC Power, Supplied from the Output. Bypass to GND with a 1.0μF ceramic capacitor, and connect to
POUT with a series 4.7
resistor (Figure 2).
6
OUT
7
AIN
Gain-Block Input. The nominal transconductance from AIN to AO is 10mS. An external P-channel
pass device can be used to build a linear regulator. The gain block can also be used as a low-battery
comparator with a threshold of 0.938V. The gain block and its associated quiescent current are
disabled by connecting AIN to OUT.
8
AO
Gain-Block Output. This open-drain N-channel output sinks current when V
AIN
< (0.75)(V
REF
). AO is
high-Z when the device is shut down, or when AIN = OUT.
9
CLK/SEL
Clock Input for the DC-DC Converter. Also serves to program the operating mode of the switcher as
follows:
CLK/SEL = LO:
Normal; operates at a fixed frequency, automatically switching to low-power mode if
load is minimized.
CLK/SEL = HI:
Forced PWM mode; operates in low-noise, constant-frequency mode at all loads.
CLK/SEL
=
Clocked:
Forced PWM mode with the internal oscillator synchronized to CLK in 500kHz
to 1200kHz range.
10, 12
PGND
Source of N-Channel Power MOSFET Switch. Connect both PGND pins together close to the device.
11, 14
LX
Inductor Connection. Connect the LX pins together close to the device.
13, 15
POUT
Power Output. P-channel synchronous rectifier source.
16
ONB
Off Control Input. When
ONB
= high and ONA = low, the IC is off. Connect
ONB
to GND for normal
operation (Table 3).
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1765 | Replaced by TMS320C6410 : Digital Signal Processors 68-PLCC -40 to 85 |
| MAX1765EEE | 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator |
| MAX1765EUE | 800mA, Low-Noise, Step-Up DC-DC Converter with 500mA Linear Regulator |
| MAX1812 | Dual USB Switch with Fault Blanking |
| MAX1812EUB | Dual USB Switch with Fault Blanking |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1763EUE+ | 功能描述:直流/直流開關轉換器 1.5A Low-Noise 1MHz Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1763EUE+T | 功能描述:直流/直流開關轉換器 1.5A Low-Noise 1MHz Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1763EUE+TG069 | 制造商:Maxim Integrated Products 功能描述: |
| MAX1763EUE-T | 功能描述:直流/直流開關轉換器 1.5A Low-Noise 1MHz Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1763EUE-TG068 | 制造商:Maxim Integrated Products 功能描述:16 PINS TSSOP PKG - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。