- 您現在的位置：買賣IC網 > PDF目錄384654 > MAX1758 (Maxim Integrated Products, Inc.) Replaced by TMS320C6410 : Digital Signal Processor 100-LQFP PDF資料下載
參數資料
| 型號： | MAX1758 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | Replaced by TMS320C6410 : Digital Signal Processor 100-LQFP |
| 中文描述： | 獨立的開關模式Li+電池充電器，內置28V開關 |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 224K |
| 代理商： | MAX1758 |
M
Stand-Alone, Switch-Mode
Li+ Battery Charger with Internal 28V Switch
______________________________________________________________________________________
11
The MAX1758 includes a state machine that controls
the charging algorithm. Figure 4 shows the state dia-
gram. Table 1 is the charging state table. When power
is applied, or
SHDN
input is driven high, the part goes
into the reset state where the timers are reset to zero to
prepare for charging. From the reset state, it enters the
prequalification state. In this state, 1/10 of the fast-
charge current charges the battery, and the battery
temperature and voltage are measured. If the voltage is
above the undervoltage threshold and the temperature
is within the limits, then it will enter the fast-charge
state. If the battery voltage does not rise above the
undervoltage threshold before the prequalification timer
expires, the charging terminates and the
FAULT
output
goes low. The prequalification time is set by the
TIMER1 capacitor (C
TIMER1
). If the battery is outside
the temperature limits, charging and the timer are sus-
pended. Once the temperature is back within limits,
charging and the timer resume.
In the fast-charge state, the
FASTCHG
output goes low
and the batteries charge with a constant current (see
Charging Current Regulator
section). If the battery volt-
age reaches the voltage limit before the fast timer
expires, the part enters the full-charge state. If the fast-
charge timer expires before the voltage limit is
reached, charging terminates and the
FAULT
output
goes low. The fast-charge time limit is set by the
TIMER2 capacitor (C
TIMER2
). If the battery temperature
is outside the limits, charging pauses and the timers
are suspended until the temperature returns to within
the limits.
In the full-charge state, the
FULLCHG
output goes low
and the batteries charge at a constant voltage (see the
Voltage Regulation
section). When the charging current
drops below 150mA (330mA peak inductor current), or
if the full-charge timer expires, the state machine enters
the top-off state. In the top-off state, the batteries con-
tinue to charge at a constant voltage until the top-off
timer expires when it enters the done state. In the done
state, charging stops until the battery voltage drops
below the recharge-voltage threshold when it enters the
reset state to start the charging process again. In the
full-charge or the top-off state, if the battery tempera-
ture is outside the limits, charging pauses and the
timers are suspended until the battery temperature
returns to within limits.
Voltage Regulator
Li+ batteries require a high-accuracy voltage limit while
charging. The MAX1758 uses a high-accuracy voltage
regulator (±0.8%) to limit the charging voltage. The bat-
tery regulation voltage is nominally set to 4.2V per cell
and can be adjusted ±5% by changing the voltage at
the V
ADJ
pin between reference voltage and ground.
By limiting the adjust range of the regulation voltage, an
overall voltage accuracy of better than 1% is main-
tained while using 1% resistors. CELL sets the cell
count from 1-to-4 series cells (see
Setting the Battery
Regulation Voltage
section).
An internal error amplifier (GMV) maintains voltage reg-
ulation (Figure 3). The GMV amplifier is compensated
at CCV. The component values shown in Figure 1 pro-
vide suitable performance for most applications.
Individual compensation of the voltage regulation and
current regulation loops allows for optimum stability.
Charging Current Regulator
The charging current-limit regulator limits the charging
current. Current is sensed by measuring the voltage
across the internal current-sense resistor R
CS
between
BATT and CS. The voltage at ISETOUT adjusts the
charging current. Full-scale charging current is
achieved when ISETOUT is connected to REF.
The charging current error amplifier (GMI) is compen-
sated at CCI. A 0.1μF capacitor at CCI provides suit-
able performance for most applications.
FAST-
CHARGE
STATE
OPEN-
DRAIN
LOW
OPEN-
DRAIN
LOW
BATTERY
CURRENT
BATTERY
VOLTAGE
FASTCHG
OUTPUT
FULLCHG
OUTPUT
FULL-
CHARGE
STATE
TOP-OFF
STATE
DONE
CHARGE I = 1C
BATTERY
INSERTION
OR SHDN HIGH
TRANSITION TO
VOLTAGE MODE
(APPROX 85% CHARGE)
FULL-CHARGE TIMER
TIMES OUT OR
BATTERY CURRENT
DROPS TO C/10
(APPROX 95% CHARGE)
TOP-OFF TIMER
TIMES OUT, END OF ALL
CHARGE FUNCTIONS
Figure 2. Charge State and Indicator Output Timing for a
Typical Charging Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1758EAI | Stand-Alone, Switch-Mode Li Battery Charger with Internal 28V Switch |
| MAX1759 | Replaced by TMS320C6410 : Digital Signal Processor 100-LQFP |
| MAX1759EUB | Buck/Boost Regulating Charge Pump in レMAX |
| MAX1760EUB | 0.8A, Low-Noise, 1MHz, Step-Up DC-DC Converter |
| MAX1761 | Small, Dual, High-Efficiency Buck Controller for Notebooks |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX17582GTL+ | 制造商:Maxim Integrated Products 功能描述:1.2MHZ LOW-COST HIGH-PERFORMANCE - Rail/Tube |
| MAX17582GTM+ | 功能描述:電流型 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX17582GTM+T | 功能描述:電流型 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX1758EAI | 功能描述:電池管理 Li+ Battery Charger w/28V Switch RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1758EAI+ | 功能描述:電池管理 Li+ Battery Charger w/28V Switch RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。