- 您現在的位置：買賣IC網 > PDF目錄384652 > MAX1666SEEE (MAXIM INTEGRATED PRODUCTS INC) Advanced Lithium-Ion Battery-Pack Protector PDF資料下載
參數資料
| 型號： | MAX1666SEEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Advanced Lithium-Ion Battery-Pack Protector |
| 中文描述： | 6-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, QSOP-16 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 294K |
| 代理商： | MAX1666SEEE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
M
Advanced Lithium-Ion
Battery-Pack Protector
10
______________________________________________________________________________________
Detailed Description
The MAX1666 battery-pack protectors supervise the
charging and discharging processes of Lithium-Ion
battery cells. Designed for 2, 3, and 4-cell applications,
these devices monitor the voltage across each cell to
provide protection against undervoltage, overvoltage,
and overcurrent damage.
Control pins
CGO
,
TKO
, and
DSO
allow control of
external MOSFET gates. This allows fast charging,
trickle charging, and discharging processes (see
Typical Operating Circuit). The voltage of each cell is
measured individually. Also, each cell is measured dif-
ferentially between every other cell of the pack.
The MAX1666 contains a state machine, a voltage reg-
ulator, an oscillator, and other logic functions to selec-
tively drive
CGO
, UVO,
TKO
,
DSO
,
WRN
, and
PKF
(Figure 1).
Modes of Operation
Shutdown Mode
The MAX1666 goes into shutdown mode when a bat-
tery pack is first connected. The quiescent current is
less than 1μA. All circuitry is inactive except the com-
parator monitoring V
SRC
and the top-cell voltage. The
MAX1666 remains in shutdown mode as long as V
SRC
is less than the top-cell voltage. When SRC is connect-
ed to an external charger and V
SRC
is 1V above the
top-cell voltage, the device goes into standby mode.
The MAX1666 returns to shutdown mode under two
conditions: the battery is disconnected and then re-
connected, or the device detects an undervoltage fault
and no charge source.
Normal Mode
The standby state activates the bias circuitry, overcur-
rent comparator, and timer. The standby state lasts
80ms, then the MAX1666 goes into the sample state for
2.5ms.
Within the 2.5ms, the MAX1666 checks for overvoltage,
undervoltage, and mismatch between cells sequential-
ly, and it stores the results in internal latches. The
MAX1666 drives the outputs according to the faults (if
any) detected by reading the latches (Figure 2) at the
end of the sample state. Then the MAX1666 returns to
the standby state.
Overvoltage Protection
The MAX1666 provides overvoltage protection to avoid
overcharging of any cell. When any cell is at overvolt-
age,
CGO
and
TKO
go high, turning off the external MOS-
FETs and stopping the charging process (Typical
Operating Circuits).
WRN
goes low. Overvoltage is set
when any cell voltage exceeds the overvoltage thresh-
old.
Overvoltage threshold is linearly adjustable through an
external 1% resistor-divider (Figure 3) from REF.
Determine the overvoltage threshold (V
OVT
) required.
V
OVT
must be between 4V and 4.4V. Set R
TOTAL
= R1
+ R2 = 1M
. Calculate R1 and R2 as follows:
R2 = [(V
OVT
- 4V) / (4.4V- 4V)]
·
R
TOTAL
R1 = R
TOTAL
- R2
MODE
TIME
TYPICAL
QUIESCENT
CURRENT (μA)
CONDITION
80ms
24
Only bias circuitry, overcurrent comparator, and timer are active.
Normal
2.5ms
250
All circuitry active.
Shutdown
—
0.7
All circuitry inactive. Device enters shutdown when it detects an undervolt-
age fault and V
SRC
< V
TOP-CELL
+ 1V (no charge source).
Table 1. Operating Modes
R1
R3
REF
OVA
UVA
MMA
R5
R2
R4
R6
GND
MAX1666
Figure 3. Using an External Resistor-Divider to Adjust
Overvoltage Threshold
STATE
Standby
Sample
—
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1666XEEP | Silver Mica Capacitor; Capacitance:180pF; Capacitance Tolerance:+/- 1%; Series:CD10; Voltage Rating:500VDC; Capacitor Dielectric Material:Mica; Termination:Radial Leaded; Lead Pitch:3.6mm; Leaded Process Compatible:No RoHS Compliant: No |
| MAX1666VEEP | Advanced Lithium-Ion Battery-Pack Protector |
| MAX1667EAP | Chemistry-Independent, Level 2 Smart Battery Charger |
| MAX1667 | Chemistry-Independent, Level 2 Smart Battery Charger |
| MAX1669EEE | Fan Controller and Remote Temperature Sensor with SMBus Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1666SEEE+T | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1666SEEE-T | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1666VEEP | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1666VEEP+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1666VEEP+T | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。