- 您現在的位置：買賣IC網 > PDF目錄9870 > MAX154BEWG+T (Maxim Integrated Products)IC ADC 8BIT 4CH W/MUX&REF 24SOIC PDF資料下載
參數資料
| 型號： | MAX154BEWG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT 4CH W/MUX&REF 24SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 位數： | 8 |
| 采樣率（每秒）： | 400k |
| 轉換器數目： | 3 |
| 功率耗散（最大）： | 75mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極 |
Interface Mode 0
Figure 5 shows the timing diagram for Mode 0 opera-
tion. This is used with microprocessors that have WAIT
state capability, whereby a READ instruction is extend-
ed to accommodate slow-memory devices. Taking CS
and RD low latches the analog multiplexer address and
starts a conversion. Data outputs DB0–DB7 remain in
the high-impedance condition until the conversion is
complete.
There are two status outputs: Interrupt (INT) and Ready
(RDY). RDY, an open-drain output (no internal pull-up
device), is connected to the processor’s READY/WAIT
input. RDY goes low on the falling edge of CS and goes
high impedance at the end of the conversion, when the
conversion result appears on the data outputs. If the
RDY output is not required, its external pull-up resistor
can be omitted. INT goes low when the conversion is
complete and returns high on the rising edge of CS or
RD.
Interface Mode 1
Mode 1 is designed for applications where the micro-
processor is not forced into a WAIT state. Taking CS
and RD low latches the multiplexer address and starts
a conversion (Figure 6). Data from the previous
conversion is immediately read from the outputs
(DB0–DB7).
INT goes high at the rising edge of CS or RD and goes
low at the end of the conversion. A second READ oper-
ation is required to read the result of this conversion.
The second READ latches a new multiplexer address
and starts another conversion. A delay of 2.5s must
be allowed between READ operations. RDY goes low
on the falling edge of CS and goes high impedance at
the rising edge of CS. If RDY is not needed, its external
pull-up resistor can be omitted.
MAX154/MAX158
CMOS High-Speed 8-Bit ADCs with
Multiplexer and Reference
_______________________________________________________________________________________
7
500ns
VIN IS TRACKED
BY INTERNAL
COMPARATORS
VIN IS SAMPLED
AND THE FOUR MSBs
ARE LATCHED
SETUP TIME REQUIRED
BY THE INTERNAL
COMPARATORS PRIOR TO
STARTING CONVERSION
600ns
RD
INT GOING LOW INDICATES
THAT CONVERSION IS
COMPLETE AND THAT
DATA CAN BE READ
1000ns
Figure 4. Operating Sequence
DATA
VALID
ADDR
VALID
ADDR
VALID
INT
RDY
RD
ANALOG
CHANNEL
ADDRESS
CS
tAS
tAH
tRDY
tCRD
HIGH IMPEDANCE
tCSS
tINTH
tDH
tACC2
tAS
tP
tCSH
Figure 5. Mode 0 Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1204AEAP+ | IC ADC 10BIT 8CH 20-SSOP |
| VE-27R-MX-F1 | CONVERTER MOD DC/DC 7.5V 75W |
| ISL3330IAZ-T7A | IC TXRX RS232/485 DUAL 20SSOP |
| HIN240CNZ-T | IC 5DRVR/5RCVR RS232 5V 44-MQFP |
| MAX11049ECB+T | IC ADC 16BIT PAR 250KSPS 64TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX154BMRG | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX154BMRG/883B | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX15500GTJ+ | 功能描述:數據轉換 IC - 多種 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX15500GTJ+T | 功能描述:數據轉換 IC - 多種 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX15501EVKIT+ | 功能描述:數據轉換 IC 開發(fā)工具 Ind Alog Crnt/Volt Output Conditioner RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發(fā)布緊急采購，3分鐘左右您將得到回復。