參數資料
型號： MAX1499
廠商： Maxim Integrated Products, Inc.
元件分類： LED驅動器
英文描述： 3.5- and 4.5-Digit. Single-Chip ADCs with LED Drivers and 礐 Interface
中文描述： 3位半和4位半、單片ADC，帶有LED驅動器和µC接口
文件頁數： 20/33頁
文件大?。?/td> 665K
代理商： MAX1499
M
3.5- and 4.5-Digit, Single-Chip ADCs with LED
Drivers and μC Interface
20
______________________________________________________________________________________
1. The calibration takes about nine cycles (1800ms).
After the calibration completes, set this bit to zero to
resume ADC conversions.
OFFSET_CAL1:
(default = 0) Automatic offset calibra-
tion enable bit. When set to 1, the MAX1497/
MAX1499 disable automatic offset calibration. When this
bit is set to zero, automatic offset calibration is enabled.
SEG_SEL:
(default = 0) SEG_SEL segment selection
bit. When set to 1, the LED segment drivers use the
LED segment registers to display individual segments
that can form letters or numbers or other information on
the display. The LED data register is not displayed.
Send the data first to the LED segment-display regis-
ters and then set this bit high.
CLR:
(default = 0) Clear all registers bit. When set to 1,
all registers reset to their power-on reset states after
CS
makes a low-to-high transition.
RANGE:
(default = 0) Input range select bit. When set
to zero, the input voltage range is ±2V. When set to 1,
the input voltage range is ±200mV.
PEAK:
(default = 0) Peak bit. When set to 1 (and the
HOLD bit is set to zero), the LED shows the result
stored in the peak register (see Table 6).
HOLD:
(default = 0) Hold bit. When set to 1, the LED
register does not update from the ADC conversion
results and holds the last result on the LED. The
MAX1497/MAX1499 continue to perform conversions
during HOLD (Table 1).
PD_ANA:
(default = 0) Power-down analog select bit.
When set to 1, the analog circuits (analog modulator
and ADC input buffers) go into the power-down mode.
When set to zero, the device is in full power-up mode.
PD_DIG:
(default = 0) Power-down digital select bit.
When set to 1, the digital circuits (digital filter and LED
drivers) go into power-down mode. This also resets the
values of the internal SRAM in the digital filter to zeros.
When set to zero, the device returns to full power-up
mode. When powering down PD_DIG, power down the
LED segment drivers by clearing the ENABLE bit to zero.
DPSET[2:1]:
(default = 00) Decimal-point selection bits
(Table 2 and 3).
DPON:
(default = 0) Decimal-point enable bit (Tables 2
and 3).
INTREF:
(default = 0) Reference select bit. For internal
reference operation, set INTREF to 1. For external refer-
ence operation, set INTREF to zero.
EXTCLK:
(default = 0) External clock select bit. The
EXTCLK bit controls selection of the internal clock or an
external clock source. A 1 in this location selects the
signal at the CLK input as the clock source. A zero in
this location selects and powers up the internal clock
oscillator.
SPI/
ADC
:
(default = 0) Display select bit. The SPI/
ADC
bit
controls selection of the data fed into LED data register.A
1 in this location selects SPI/QSPI/ MICROWIRE data
(user writes this data to the LED data register). A zero in
this location selects the ADC result register data, unless
hold or peak functions are active (Table 1).
Note:
When changing any one of the following control
bits:
OFFSET_CAL1
, RANGE, PD_ANA, PD_DIG,
INTREF, and EXTCLK, wait 800ms before reading the
ADC results.
Overrange Register (Read/Write)
MSB
D15
LSB
D0
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
Default values:
7CF0h (for 3.5-digit, +1999)
4E1Fh (for 4.5-digit, +19,999)
The overrange register is a 16-bit read/write register
(D15 is the MSB). When the conversion result exceeds
the value in the overrange register, the OVER bit in the
status register latches to 1. The LED shows a 1 followed
by four dashes for the MAX1499 or a 1 followed by
three dashes for the MAX1497 (Table 4).
The data is represented in two’s complement format.
相關PDF資料
PDF描述
MAX1497EAI 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers and レC Interface
MAX1499ECJ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers and レC Interface
MAX15004 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers
MAX15004AAUE 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers
MAX15004BAUE 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers
相關代理商/技術參數
參數描述
MAX14998ETO+ 功能描述:模擬開關 IC 4Ch DisplayPort MUX RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
MAX14998ETO+T 功能描述:模擬開關 IC 4Ch DisplayPort MUX RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
MAX1499ECJ 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1499ECJ+ 功能描述:模數轉換器 - ADC 4.5 Digit ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1499ECJ+T 功能描述:模數轉換器 - ADC 4.5 Digit ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*