- 您現在的位置：買賣IC網 > PDF目錄383323 > MAX1497 (Maxim Integrated Products, Inc.) 3.5- and 4.5-Digit. Single-Chip ADCs with LED Drivers and 礐 Interface PDF資料下載
參數資料
| 型號： | MAX1497 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | LED驅動器 |
| 英文描述： | 3.5- and 4.5-Digit. Single-Chip ADCs with LED Drivers and 礐 Interface |
| 中文描述： | 3位半和4位半、單片ADC，帶有LED驅動器和µC接口 |
| 文件頁數： | 19/33頁 |
| 文件大?。?/td> | 665K |
| 代理商： | MAX1497 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
M
3.5- and 4.5-Digit, Single-Chip ADCs with LED
Drivers and μC Interface
______________________________________________________________________________________
19
Default values: 00h
This register contains the status of the conversion
results.
SIGN:
Latched negative-polarity indicator. Latches
high when the result is negative. Clears by reading the
status register, unless the condition remains true.
OVER:
Overrange bit. Latches high if an overrange
condition occurs (the ADC result is larger than the
value in the overrange register). Clears by reading the
status register, unless the condition remains true.
UNDER:
Underrange bit. Latches high if an under-
range condition occurs (the ADC result is less than the
value in the underrange register). Clears by reading the
status register, unless the condition remains true.
LOW_BATT:
Low-battery bit. Latches high if the volt-
age at the LOWBATT is lower than 2.048V (typ). Clears
by reading the status register, unless the condition
remains true. For the MAX1497, LOWBATT is not used
and the LOWBATT bit always returns to zero.
DRDY:
Data ready bit. Latches high to indicate a com-
pleted conversion result with valid data. Read the ADC
result register to clear this bit.
Control and Status Registers
Command Byte (Write Only)
Status Register (Read Only)
MSB
LSB
Bit 7
Bit 6
R/
W
Bit 5
RS4
Bit 4
RS3
Bit 3
RS2
Bit 2
RS1
Bit 1
RS0
Bit 0
X
START(1)
MSB
LSB
0
SIGN
OVER
UNDER
LOW_BATT
DRDY
0
0
Control Register (Read/Write)
MSB
Bit 15
SPI/
ADC
Bit 14
EXTCLK
Bit 13
INTREF
Bit 12
DPON
Bit 11
DPSET2
Bit 10
DPSET1
Bit 9
PD_DIG
Bit 8
PD_ANA
LSB
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
HOLD
PEAK
RANGE
CLR
SEG_SEL
OFFSET_CAL1
OFFSET_
CAL2
ENABLE
START:
Start bit. The first 1 clocked into the MAX1497/
MAX1499 is the first bit of the command byte.
(R/
W
):
Read/
Write
. Set this bit to 1 to read from the
specified register. Set this bit to zero to write to the
selected register. Note that certain registers are read
only. Write commands to a read-only register are
ignored.
(RS4–RS0):
Register address bits. RS4 to RS0 specify
which register is accessed.
X:
Don’t care.
Default values: 0001h
This register is the primary control register for the
MAX1497/MAX1499. It is a 16-bit read/write register. It
is used to indicate the desired clock and reference
source. It sets the LED display controls, range modes,
power-down modes, offset calibration, and the reset
register function (CLR).
ENABLE:
(default = 1) LED driver enable bit. When set to
1, the MAX1497/MAX1499 enables the LED display dri-
vers. A 0 in this location disables the LED display drivers.
OFFSET_CAL2:
(default = 0) Enhanced offset-calibra-
tion start bit (MAX1499, RANGE = 1). To achieve the
lowest possible offset in the
±
200mV input range, per-
form an enhanced offset calibration by setting this bit to
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1499 | 3.5- and 4.5-Digit. Single-Chip ADCs with LED Drivers and 礐 Interface |
| MAX1497EAI | 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers and レC Interface |
| MAX1499ECJ | 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers and レC Interface |
| MAX15004 | 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers |
| MAX15004AAUE | 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14970ETP+ | 制造商:Maxim Integrated Products 功能描述:RUGGEDIZED SATA 6GBPS REDRIVER WITH HIGH ESD AND EXTENDED TE - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC REDRIVER RUGGED 6GBPS QFN 制造商:Maxim Integrated Products 功能描述:Equalizers ruggedized sata 6gbp s redriver with high |
| MAX14970ETP+T | 制造商:Maxim Integrated Products 功能描述:RUGGEDIZED SATA 6GBPS REDRIVER WITH HIGH ESD AND EXTENDED TE - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC REDRIVER SATA GEN 3 QFN 制造商:Maxim Integrated Products 功能描述:ruggedized sata 6gbp s redriver with high |
| MAX14970EVKIT# | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR MAX14970. RUGGEDIZED SATA 6GBPS REDRIVER - Boxed Product (Development Kits) 制造商:Maxim Integrated Products 功能描述:KIT EVALUATION FOR MAX14970 制造商:Maxim Integrated Products 功能描述:Equalizers MAX14970 Eval Kit |
| MAX14972CTG+ | 功能描述:USB 接口集成電路 Dual USB 3.0 Re-Driver RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MAX14972CTG+T | 功能描述:USB 接口集成電路 Dual USB 3.0 Re-Driver RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。