- 您現在的位置：買賣IC網 > PDF目錄383323 > MAX1487ESA (MAXIM INTEGRATED PRODUCTS INC) Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers PDF資料下載
參數資料
| 型號： | MAX1487ESA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers |
| 中文描述： | LINE TRANSCEIVER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 133K |
| 代理商： | MAX1487ESA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁
M
±15kV ES D-Protec ted, S lew-Rate-Limited,
Low-Power, RS -485/RS -422 Transc eivers
12
______________________________________________________________________________________
The major difference between tests done using the
Human Body Model and IEC1000-4-2 is higher peak
current in IEC1000-4-2, because series resistance is
lower in the IEC1000-4-2 model. Hence, the ESD with-
stand voltage measured to IEC1000-4-2 is generally
lower than that measured using the Human Body
Model. Figure 7 shows the current waveform for the 8kV
IEC1000-4-2 ESD contact-discharge test.
The air-gap test involves approaching the device with a
charged probe. The contact-discharge method connects
the probe to the device before the probe is energized.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resis-
tance. Its objective is to emulate the stress caused by
contact that occurs with handling and assembly during
manufacturing. Of course, all pins require this protec-
tion during manufacturing—not just inputs and outputs.
Therefore, after PC board assembly, the Machine Model
is less relevant to I/O ports.
MAX 487E/MAX 1487E:
128 T ransc eivers on the Bus
The 48k
, 1/4-unit-load receiver input impedance of the
MAX487E and MAX1487E allows up to 128 transceivers
on a bus, compared to the 1-unit load (12k
input
impedance) of standard RS-485 drivers (32 transceivers
maximum). Any combination of MAX487E/MAX1487E
and other RS-485 transceivers with a total of 32 unit
loads or less can be put on the bus. The MAX481E,
MAX483E, MAX485E, and MAX488E–MAX491E have
standard 12k
receiver input impedance.
MAX 483E/MAX 487E/MAX 488E/MAX 489E:
Reduc ed EMI and Reflec tions
The MAX483E and MAX487E–MAX489E are slew-rate
limited, minimizing EMI and reducing reflections
caused by improperly terminated cables. Figure 16
shows the driver output waveform and its Fourier analy-
sis of a 150kHz signal transmitted by a MAX481E,
MAX485E, MAX490E, MAX491E, or MAX1487E. High-
frequency harmonics with large amplitudes are evident.
Figure 17 shows the same information displayed for a
MAX483E, MAX487E, MAX488E, or MAX489E transmit-
ting under the same conditions. Figure 17’s high-fre-
quency harmonics have much lower amplitudes, and
the potential for EMI is significantly reduced.
Low-Power S hutdown Mode
(MAX 481E/MAX 483E/MAX 487E)
A low-power shutdown mode is initiated by bringing
both RE high and DE low. The devices will not shut
down unless both the driver and receiver are disabled.
In shutdown, the devices typically draw only 0.5μA of
supply current.
RE and DE may be driven simultaneously; the parts are
guaranteed not to enter shutdown if RE is high and DE
is low for less than 50ns. If the inputs are in this state
for at least 600ns, the parts are guaranteed to enter
shutdown.
For the MAX481E, MAX483E, and MAX487E, the t
ZH
and t
ZL
enable times assume the part was not in the
low-power shutdown state (the MAX485E, MAX488E–
MAX491E, and MAX1487E can not be shut down). The
t
ZH(SHDN)
and t
ZL(SHDN)
enable times assume the
parts were shut down (see Electrical Characteristics).
500kHz/div
0Hz
5MHz
10dB/div
Figure 16. Driver Output Waveform and FFT Plot of
MAX485E/MAX490E/MAX491E/MAX1487E Transmitting a
150kHz Signal
500kHz/div
0Hz
5MHz
10dB/div
Figure 17. Driver Output Waveform and FFT Plot of
MAX483E/MAX487E–MAX489E Transmitting a 150kHz Signal
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1487MJA | Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers |
| MAX1487ECPA | 【15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS-485/RS-422 Transceivers |
| MAX1487ECSA | 【15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS-485/RS-422 Transceivers |
| MAX1488 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX1488EESD | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1487ESA+ | 功能描述:RS-422/RS-485 接口 IC RS-485/RS-422 Transceiver RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX1487ESA+T | 功能描述:RS-422/RS-485 接口 IC RS-485/RS-422 Transceiver RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX1487ESA-T | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX1487MJA | 制造商:Maxim Integrated Products 功能描述:8 PIN CERDIP, -55 + 125 TEMP, TRANSCEIVER - Rail/Tube |
| MAX14885EETL+ | 功能描述:視頻開關 IC Low Cap VGA 2:2 Dual Graphics Crx Switch RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。