- 您現在的位置：買賣IC網 > PDF目錄11739 > MAX14821ETG+T (Maxim Integrated Products)IC IO-LINK 24-TQFN PDF資料下載
參數資料
| 型號： | MAX14821ETG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/31頁 |
| 文件大小： | 0K |
| 描述： | IC IO-LINK 24-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
MAX14821
IO-Link Device Transceiver
17
Maxim Integrated
DO Fault Detection
The device registers a DoFault event when a short circuit
is present at the DO output for 440Fs. A short condition
exists when the load current on the DO driver exceeds
the 135mA (typ) DO current limit. When a short-circuit
condition is detected, the DO driver enters autoretry
mode. In autoretry mode the device periodically checks
whether the error is still present. Autoretry attempts last
for 440s (typ) and occur every 26ms (typ). When a
DoFault error is detected, the DoFault and DoFaultInt bits
are set, IRQ asserts, and the driver is turned off 440s
(typ) after the start of the DO faults.
Reverse-Polarity Protection
The device is protected against reverse-polarity connec-
tions on VCC, C/Q, DO, DI, and GND. Any combination
of these pins can be connected to DC voltages up to
40V (max). A short to 40V results in a current flow of less
than 500FA.
Ensure that the maximum voltage between any of these
pins does not exceed 40V.
5V and 3.3V Linear Regulators
The device includes two internal regulators to generate 5V
(V5) and 3.3V (LDO33). LDO5 is specified for 10mA total
external load current (i.e., LDO33 + V5) when bypassed
with a 0.1F capacitor to ground. Add the compensation
network shown in Figure 7 to draw up to 30mA of total
external load current from the 5V LDO. LDO33 is speci-
fied at 20mA. The input of V5, LDOIN, can be powered
from VP, the protected 24V supply output, or to another
voltage in the 7V to 36V range.
If the external circuits that are powered by the linear reg-
ulators require an input bypass capacitance larger than
100nF for 5V or 1F for 3.3V, a compensation network
must be added on V5 and/or LDO33. The compensation
network consists of a 10
W series resistor and a capaci-
tor equal to the value required by the external circuit,
as shown in Figure 14. The capacitors C33* and C5*
in Figure 14 represent the capacitance required by the
external circuits. Figure 14 does not show any protection
diodes for simplicity.
When the internal 5V LDO is not used, V5 becomes the
supply input for the internal analog and digital func-
tions and thus has to be supplied externally so that
the MAX14820 operates normally. The 5V LDO can be
disabled by connecting LDOIN to V5. Apply an external
voltage of 4.75V to 5.25V to V5 when the LDO is disabled.
Use the LDO33Dis bit in the Mode register to disable
LDO33. See the Mode Register [R1, R0] = [1,1] section
for more information. V5 and LDO33 are not protected
against short circuits.
Power-Up
The C/Q and DO driver outputs and the UV output are
high impedance when VCC, V5, VL, and/or LDO33 volt-
ages are below their respective undervoltage thresh-
olds during power-up. UV goes low and the drivers are
enabled when all these voltages exceed their respective
undervoltage-lockout thresholds.
The drivers are automatically disabled if VCC, V5, or VL
falls below its threshold.
Undervoltage Detection
The device monitors VCC, V5, VL, and optionally LDO33
for undervoltage conditions. UV is high impedance when
any monitored voltage falls below its UVLO threshold.
VCC, V5, and VL undervoltage detection cannot be disabled.
When VCC falls below the VCCUVLO threshold, the UV24 and
UV24Int bits are set, UV asserts high, and IRQ asserts low.
Figure 7. V5 Compensation Network
Figure 8. Larger Bypass Capacitance for Powering External
Circuits
MAX14821
10
0.1F
1F
V5
VL
5V
LDO33
3.3V
MAX14821
V5
0.1F
10W
3.3V
5V
LDO33
C5
1F
10W
C33
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C774-I/L | IC MCU OTP 4KX14 A/D PWM 44PLCC |
| DSPIC33FJ32GS610-I/PF | IC MCU/DSP 32KB FLASH 100TQFP |
| MS27484T22B55S | CONN PLUG 55POS STRAIGHT W/SCKT |
| MS27484E18A35P | CONN PLUG 66POS STRAIGHT W/PINS |
| PIC18LF4553-I/PT | IC PIC MCU FLASH 16KX16 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14821EVKIT# | 功能描述:界面開發工具 MAX14820/21 EVAL KIT RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX14821EWA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX14821EWA+T | 功能描述:輸入/輸出控制器接口集成電路 100mA IO-Link Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14824ETG+ | 功能描述:輸入/輸出控制器接口集成電路 IO-Link Master Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14824ETG+T | 功能描述:輸入/輸出控制器接口集成電路 IO-Link Master Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。