- 您現在的位置：買賣IC網 > PDF目錄383320 > MAX1478AAE (MAXIM INTEGRATED PRODUCTS INC) 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner PDF資料下載
參數資料
| 型號： | MAX1478AAE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | 5.30 MM, 0.65 MM PITCH, SSOP-16 |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 210K |
| 代理商： | MAX1478AAE |
FSO TC Compensation
Silicon piezoresistive transducers (PRTs) exhibit a large
positive input resistance tempco (TCR) so that, while
under constant current excitation, the bridge voltage
(V
BDRIVE
) increases with temperature. This depen-
dence of V
BDRIVE
on the sensor temperature can be
used to compensate the sensor temperature errors.
PRTs also have a large negative full-span output sensi-
tivity tempco (TCS) so that, with constant voltage exci-
tation, FSO will decrease with temperature, causing a
full-span output temperature coefficient (FSO TC) error.
However, if the bridge voltage can be made to increase
with temperature at the same rate that TCS decreases
with temperature, the FSO will remain constant.
FSO TC compensation is accomplished by resistor
R
FTC
and the FSOTC DAC, which modulate the excita-
tion reference current at ISRC as a function of tempera-
ture (Figure 3). FSO DAC sets V
ISRC
and remains
constant with temperature, while the voltage at FSOTC
varies with temperature. FSOTC is the buffered output
of the FSOTC DAC. The reference DAC voltage is
V
BDRIVE
, which is temperature dependent. The FSOTC
DAC alters the tempco of the current source. When the
tempco of the bridge voltage is equal in magnitude and
opposite in polarity to the TCS, the FSO TC errors are
compensated and FSO will be constant with tempera-
ture.
Offset TC Compensation
Compensating offset TC errors involves first measuring
the uncompensated offset TC error, then determining
the percentage of the temperature-dependent voltage
V
BDRIVE
that must be added to the output summing
junction to correct the error. Use the Offset TC DAC to
adjust the amount of BDRIVE voltage that is added to
the output summing junction (Figure 2).
Analog Signal Path
The fully differential analog signal path consists of four
stages:
Front-end summing junction for coarse offset correction
3-bit PGA with eight selectable gains ranging from
41 through 230
Three-input-channel summing junction
Differential to single-ended output buffer (Figure 2)
Coarse Offset Correction
The sensor output is first fed into a differential summing
junction (INM (negative input) and INP (positive input))
with a CMRR >90dB, an input impedance of approxi-
mately 1M
, and a common-mode input voltage range
from V
SS
to V
DD
. At this summing junction, a coarse off-
set-correction voltage is added, and the resultant volt-
age is fed into the PGA. The 3-bit (plus sign)
input-referred Offset DAC (IRO DAC) generates the
coarse offset-correction voltage. The DAC voltage ref-
erence is 1.25% of V
DD
; thus, a V
DD
of 5V results in a
front-end offset-correction voltage ranging from -63mV
to +63mV, in 9mV steps (Table 1). To add an offset to
the input signal, set the IRO sign bit high; to subtract an
offset from the input signal, set the IRO sign bit low.
The IRO DAC bits (C2, C1, C0, and IRO sign bit) are
programmed in the configuration register (see
Internal
EEPROM
section).
M
1% Accurate, Digitally Trimmed,
Rail-to-Rail Sensor Signal Conditioner
_______________________________________________________________________________________
5
V
PRESSURE
P
MIN
P
MAX
FULL SCALE (FS)
4.5
0.5
FULL-SPAN OUTPUT (FSO)
OFFSET
Figure 1. Typical Pressure-Sensor Output
SOTC
BDRIVE
1.25% V
DD
SOFF
±
±
A2
INP
INM
A1 A0
PGA
Σ
Σ
A = 1
OUT
A = 2.3
A = 2.3
OFFTC
DAC
IRO
DAC
V
DD
OFFSET
DAC
Figure 2. Signal-Path Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1479EVKIT-315 | Evaluation Kit |
| MAX1479EVKIT-433 | Evaluation Kit |
| MAX147ACAP | +2.7Low-Power, 8-Channel, Serial 12-Bit ADCs |
| MAX147AEAP | +2.7Low-Power, 8-Channel, Serial 12-Bit ADCs |
| MAX146ACAP | .1 UF/400VDC METAL POLY CAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1478AAE-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1478CAE | 功能描述:板上安裝溫度傳感器 Rail-to-Rail Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1478CAE-T | 功能描述:板上安裝溫度傳感器 Rail-to-Rail Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1479ATE | 功能描述:射頻發射器 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| MAX1479ATE+ | 功能描述:射頻發射器 300MHz - 450MHz ASK/FSK Transmitter RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。