- 您現在的位置：買賣IC網 > PDF目錄383320 > MAX1478 (Maxim Integrated Products, Inc.) 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner PDF資料下載
參數資料
| 型號： | MAX1478 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner |
| 中文描述： | 1%精確度、數字校準、滿擺幅傳感器信號調理器 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 210K |
| 代理商： | MAX1478 |
Detailed Description of the Digital Lines
Chip Select (CS) and Write Enable (WE)
CS is used to enable OUT, control serial communica-
tion, and force an update of the configuration and DAC
registers.
A low on CS disables serial communication.
A transition from low to high on CS forces an update
of the configuration and DAC registers from the
EEPROM when the U bit is zero.
A transition from high to low on CS terminates pro-
gramming mode.
A logic high on CS enables OUT and serial commu-
nication (see
Communication Protocol
section).
WE controls the refresh rate for the internal configura-
tion and DAC registers from the EEPROM and enables
the erase/write operations. If communication has been
initiated (see
Communication Protocol
section), internal
register refresh is disabled.
A low on WE disables the erase/write operations and
also disables register refreshing from the EEPROM.
A high on WE selects a refresh rate of approximately
400 times per second and enables EEPROM
erase/write operations.
It is recommended that WE be connected to V
SS
after the MAX1478 EEPROM has been programmed.
Serial Clock
Serial Clock (SCLK) must be driven externally. It is
used to input commands to the MAX1478 and read
EEPROM contents. Input data on DIO is latched on the
rising edge of SCLK. Noise on SCLK may disrupt com-
munication. In noisy environments, place a capacitor
(0.01μF) between SCLK and V
SS
.
Data Input/Output
The data input/output (DIO) line is an input/output pin
used to issue commands to the MAX1478 (input mode)
or read the EEPROM contents (output mode).
In input mode (the default mode), data on DIO is
latched on each rising edge of SCLK. Therefore, data
on DIO must be stable at the rising edge of SCLK and
should transition on the falling edge of SCLK.
DIO will switch to output mode after receiving a READ
EEPROM command, and will return the data bit
addressed by the digital value in the READ EEPROM
command. After a low-to-high transition on CS, DIO
returns to input mode and is ready to accept more
commands.
Communication Protocol
To initiate communication, the first 6 bits on DIO after
CS transitions from low to high
must
be 1010U0
(defined as the INIT SEQUENCE). The MAX1478 will
then begin accepting 16-bit control words (Figure 4).
If the INIT SEQUENCE is not detected, all subsequent
data on DIO is ignored until CS again transitions from
low to high and the correct INIT SEQUENCE is received.
The U bit of the INIT SEQUENCE controls the updating
of the DACs and configuration register from the internal
EEPROM. If this bit is low (U = 0), all four internal DACs
and the configuration register will be updated from the
EEPROM on the next rising edge of CS (this is also the
default on power-up). If the U bit is high, the DACs and
configuration register will not be updated from the inter-
nal EEPROM; they will retain their current value on any
subsequent CS rising edge. The MAX1478 continues to
accept control words until CS is brought low.
M
1% Accurate, Digitally Trimmed,
Rail-to-Rail Sensor Signal Conditioner
_______________________________________________________________________________________
9
Figure 4. Communication Sequence
CS
SCLK
DIO
t
MIN
200
μ
s
16 CLK
CYCLES
BEGIN
PROGRAMMING
SEQUENCE
CONTROL
WORD
CONTROL
WORD
CONTROL
WORDS
16 CLK
CYCLES
n x 16 CLK
CYCLES
X
1
0
1
D0
D0
D1
D1
CM3
CM3
0
U
0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1478AAE | 1% Accurate, Digitally Trimmed,Rail-to-Rail Sensor Signal Conditioner |
| MAX1479EVKIT-315 | Evaluation Kit |
| MAX1479EVKIT-433 | Evaluation Kit |
| MAX147ACAP | +2.7Low-Power, 8-Channel, Serial 12-Bit ADCs |
| MAX147AEAP | +2.7Low-Power, 8-Channel, Serial 12-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14780EEPA+ | 功能描述:RS-422/RS-485 接口 IC PROFIBUS RS-485 Transceiver RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX14780EESA+ | 功能描述:RS-422/RS-485 接口 IC PROFIBUS RS-485 Transceiver RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX14780EESA+T | 功能描述:RS-422/RS-485 接口 IC PROFIBUS RS-485 Transceiver RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX14783EASA+ | 制造商:Maxim Integrated Products 功能描述:HALF DUPLEX, DUAL VOLTAGE (3V TO 5.5V), HIGH ESD HBM (+/-35K - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC TXRX RS485/422 ESD 8SO |
| MAX14783EASA+T | 制造商:Maxim Integrated Products 功能描述:HALF DUPLEX, DUAL VOLTAGE (3V TO 5.5V), HIGH ESD HBM (+/-35K - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TXRX RS485/422 ESD 8SO |
發布緊急采購，3分鐘左右您將得到回復。