- 您現在的位置：買賣IC網 > PDF目錄16288 > MAX14566EEVKIT# (Maxim Integrated Products)EVAL KIT PDF資料下載
參數資料
| 型號： | MAX14566EEVKIT# |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL KIT |
| 標準包裝： | 1 |
| 系列： | * |
MAX14566E/MAX14566AE/MAX14566BE
USB Host Charger Identification
Analog Switches
13
Bus Voltage Discharge
The MAX14566AE automatic current-limit switch control
output can be used to discharge the VBUS during VBUS
reset. When the system controls the current-limit switch
for VBUS toggle, the output capacitor can be discharged
slowly depending upon the load. If fast discharge of the
VBUS capacitor is desired, the CEN output can be used
to achieve the fast discharge as shown in Figure 7.
Data Contact Detect
All the devices support USB devices that require detect-
ing the USB data lines prior to charging. When a USB
Revision 1.2-compliant device is attached, the USB data
lines DP and DM are shorted together. The short remains
until it is detected by the USB device. This feature guar-
antees appropriate charger detection if a USB Revision
1.2-compliant device is attached. The autodetection
charger mode is activated after the data contact detect
is established. CB must be set low to activate data con-
tact detect.
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents test
setup, test methodology, and test results.
Extended ESD Protection
(Human Body Model)
ESD-protection structures are incorporated on all pins
to protect against electrostatic discharges up to Q2kV
(HBM) encountered during handling and assembly. DP
and DM are further protected against ESD up to Q15kV
(HBM) without damage. The ESD structures withstand
high ESD both in normal operation and when the device
is powered down. After an ESD event, the device contin-
ues to function without latchup (Figure 8).
Figure 7. MAX14566AE VBUS Discharge Circuit
MAX14566AE
USB
TRANSCEIVER
CURRENT-LIMIT
SWITCH
CLS EN
SYSTEM CONTROL
STANDBY
CB
CEN
+5V POWER
SUPPLY
EN
VCC
TDM
TDP
0.1F
10kI
1kI
150F
GND
USB
CONNECTION
D+
DP
GND
VCC
D-
VBUS
DM
相關PDF資料 |
PDF描述 |
|---|---|
| RSM08DRYH-S13 | CONN EDGECARD 16POS .156 EXTEND |
| MAX98089EVKIT#WLP | KIT EVAL FOR MAX98089-WLP |
| RMM08DRYH-S13 | CONN EDGECARD 16POS .156 EXTEND |
| MAX98089EVKIT#TQFN | KIT EVAL FOR MAX98089-TQFN |
| GBM24DSEF-S13 | CONN EDGECARD 48POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14566EEVKIT# | 功能描述:交換機 IC 開發工具 MAX14566E Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX14566ETA+T | 功能描述:模擬開關 IC USB HiSpeed an swtch w/USB host chrgr IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX14566EVKIT+ | 功能描述:交換機 IC 開發工具 MAX14566 EVKIT RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX14568EEWA+T | 功能描述:多路器開關 IC Dual 8:2 MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX14569EEE+ | 功能描述:轉換 - 電壓電平 Dual LLT w/Cpump & ESD Protection RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
發布緊急采購，3分鐘左右您將得到回復。