- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX1455AUE+T (Maxim Integrated Products)IC AUTO SNSR SIGNAL COND 16TSSOP PDF資料下載
參數資料
| 型號： | MAX1455AUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/25頁 |
| 文件大小： | 0K |
| 描述： | IC AUTO SNSR SIGNAL COND 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 自動 |
| 輸入類型： | 模擬 |
| 輸出類型： | 模擬 |
| 電流 - 電源： | 6mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
Serial Digital Output
DIO is configured as a digital output by writing a Read
IRS (RDIRS) command (5 hex) to the CRIL location. On
receipt of this command, the MAX1455 outputs a byte
of data, the contents of which are determined by the
IRS pointer (IRSP[3:0]) value at location IRSA[3:0] =
8hex. The data is output as a single byte, framed by a
start bit and a stop bit. Table 11 lists the data returned
for each IRSP address value.
Once the RDIRS command has been sent, all connec-
tions to DIO must be three-stated to allow the MAX1455
to drive the DIO line. Following receipt of the RDIRS
command, the MAX1455 drives DIO high after 1 byte
time. The MAX1455 holds DIO high for a single bit time
and then asserts a start bit (drives DIO low). The start
bit is then followed by the data byte and a stop bit.
Immediately following transmission of the stop bit, the
MAX1455 three-states DIO, releasing the line. The
MAX1455 is then ready to receive the next command
sequence 1 byte time after release of DIO.
Note that there are time intervals before and after the
MAX1455 sends the data byte when all devices on the
DIO line are three-stated. It is recommended that a
weak pullup resistor be applied to the DIO line during
these time intervals to prevent unwanted transitions
(Figure 4). In applications where DIO and analog out-
put (OUT) are not connected, a pullup resistor should
be permanently connected to DIO. If the MAX1455 DIO
and analog outputs are connected, then do not load
this common line during analog measurements. In this
situation, perform the following sequence:
1) Connect a pullup resistor to the DIO/OUT line,
preferably with a relay.
2) Send the RDIRS command.
3) Three-state the user connection (set to high imped-
ance).
4) Receive data from the MAX1455.
5) Activate the user connection (pull DIO/OUT line high).
6) Release the pullup resistor.
MAX1455
Low-Cost Automotive Sensor Signal
Conditioner
______________________________________________________________________________________
13
IRO SIGN, IRO[2:0]
INPUT-REFERRED OFFSET
CORRECTION AS % OF VDD
INPUT-REFERRED OFFSET, CORRECTION
AT VDD = 5VDC IN mV
1,111
+1.25
+63
1,110
+1.08
+54
1,101
+0.90
+45
1,100
+0.72
+36
1,011
+0.54
+27
1,010
+0.36
+18
1,001
+0.18
+9
1,000
0
0,000
0
0,001
-0.18
-9
0,010
-0.36
-18
0,011
-0.54
-27
0,100
-0.72
-36
0,101
-0.90
-45
0,110
-1.08
-54
0,111
-1.25
-63
Table 7. Input Referred Offset (IRO[2:0])
相關PDF資料 |
PDF描述 |
|---|---|
| MAX14566AEETA+T | IC USB SWITCH HOST CHARGER 8TDFN |
| MAX14582EWC+T | IC TXRX USB 2.0 FS 5WIRE 12WLP |
| MAX14626ETT+T | IC CURR LOOP PROT 4-20MA 6TDFN |
| MAX1464AAI+T | IC SENSOR SIGNAL COND 28-SSOP |
| MAX1474AXT+T | IC ELECTRONIC CAPACITOR SC70-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1455C/D | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1455C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX1455EAE | 功能描述:板上安裝溫度傳感器 Automotive Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1455EAE-T | 功能描述:板上安裝溫度傳感器 Automotive Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1455EUE | 功能描述:板上安裝溫度傳感器 Automotive Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。