- 您現在的位置：買賣IC網 > PDF目錄16180 > MAX1452EVKIT-CS (Maxim Integrated Products)EVAL KIT FOR MAX1452 PDF資料下載
參數資料
| 型號： | MAX1452EVKIT-CS |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 22/25頁 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX1452 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | 接口，傳感器信號調節器 |
| 已用 IC / 零件： | MAX1452 |
| 已供物品： | 板 |
MAX1452
Low-Cost Precision Sensor
Signal Conditioner
6
Maxim Integrated
Detailed Description
The MAX1452 provides amplification, calibration, and
temperature compensation to enable an overall perfor-
mance approaching the inherent repeatability of the
sensor. The fully analog signal-path introduces no
quantization noise in the output signal while enabling
digitally controlled trimming with the integrated 16-bit
DACs. Offset and span can be calibrated to within
±0.02% of span.
The MAX1452 architecture includes a programmable
sensor excitation, a 16-step programmable-gain ampli-
fier (PGA), a 768-byte (6144 bits) internal EEPROM, four
16-bit DACs, an uncommitted op amp, and an on-chip
temperature sensor.The MAX1452 also provides a
unique temperature compensation strategy for offset
TC and FSOTC that was developed to provide a
remarkable degree of flexibility while minimizing testing
costs.
The customer can select from one to 114 temperature
points to compensate their sensor. This allows the lati-
tude to compensate a sensor with a simple first order
linear correction or match an unusual temperature
curve. Programming up to 114 independent 16-bit EEP-
ROM locations corrects performance in 1.5°C tempera-
ture increments over a range of -40°C to +125°C. For
sensors that exhibit a characteristic temperature perfor-
mance, a select number of calibration points can be
used with a number of preset values that define the
temperature curve. In cases where the sensor is at a
different temperature than the MAX1452, the MAX1452
uses the sensor bridge itself to provide additional tem-
perature correction.
The single pin, serial Digital Input-Output (DIO) commu-
nication architecture and the ability to timeshare its
activity with the sensor’s output signal enables output
sensing and calibration programming on a single line
by parallel connecting OUT and DIO. The MAX1452
provides a Secure-Lock feature that allows the cus-
tomer to prevent modification of sensor coefficients and
the 52-byte user definable EEPROM data after the sen-
sor has been calibrated. The Secure-Lock feature also
provides a hardware override to enable factory rework
and recalibration by assertion of logic high on the
UNLOCK pin.
The MAX1452 allows complete calibration and sensor
verification to be performed at a single test station.
Once calibration coefficients have been stored in the
MAX1452, the customer can choose to retest in order to
verify performance as part of a regular QA audit or to
generate final test data on individual sensors.
The MAX1452’s low current consumption and the inte-
grated uncommitted op amp enables a 4–20mA output
signal format in a sensor that is completely powered
from a 2-wire current loop. Frequency response can be
user-adjusted to values lower than the 3.2kHz band-
width by using the uncommitted op amp and simple
passive components.
The MAX1452 (Figure 1) provides an analog amplifica-
tion path for the sensor signal. It also uses an analog
architecture for first-order temperature correction. A
digitally controlled analog path is then used for nonlin-
ear temperature correction. Calibration and correction
is achieved by varying the offset and gain of a pro-
grammable-gain-amplifier (PGA) and by varying the
Pin Description (continued)
PIN
SSOP/TSSOP
TQFN-EP
NAME
FUNCTION
911
VDDF
Positive Supply Voltage for EEPROM. Connect a 1F capacitor from
VDDF to VSS. Connect VDDF to VDD or for improved noise performance
connect a 30
Ω resistor to VDD.
10
12
UNLOCK
Secure-Lock Disable. Allows communication to the device.
11
14
DIO
Digital Input Output. DIO allows communication with the device.
12
15
CLK1M
1MHz Clock Output. The output can be controlled by a configuration bit.
13
17
AMPOUT
Uncommitted Amplifier Output
14
18
AMP-
Uncommitted Amplifier Negative Input
15
19
AMP+
Uncommitted Amplifier Positive Input
16
21
FSOTC
Full Span TC Buffered Output
—
EP
Exposed Pad (TQFN Only). Internally connected; connect to VSS.
相關PDF資料 |
PDF描述 |
|---|---|
| CMH322522-R56KL | INDUCTOR WIREWOUND .56UH 1210 |
| VI-J5P-EY-S | CONVERTER MOD DC/DC 13.8V 50W |
| 382LX333M035A052 | CAP ALUM 33000UF 35V 20% SNAP |
| 5500R-107K | HIGH CURRENT POWER CHOKE 100K UH |
| ACC07DREF-S13 | CONN EDGECARD 14POS .100 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1452EVKIT-NS | 功能描述:數據轉換 IC 開發工具 Low-Cost Precision Sensor Signal Conditioner RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1452EVKIT-NS+ | 功能描述:數據轉換 IC 開發工具 Programmers, Development Systems Eval and Demo Boards and Kits - KIT EVAL MAX1452-NS RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1452KEY | 功能描述:溫度傳感器開發工具 MAX1455 Eval Kit RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| MAX14530EEVKIT+ | 制造商:Maxim Integrated Products 功能描述:OVERVOLTAGE PROTECTION WITH USB CHARGER DETECTION LDO AND ES - Boxed Product (Development Kits) |
| MAX14530EEWC+T | 制造商:Maxim Integrated Products 功能描述:OVERVOLTAGE PROTECTION WITH CHARGER DETECTION - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。