參數資料
型號： MAX1452EAE+T
廠商： Maxim Integrated Products
文件頁數： 5/25頁
文件大?。?/td> 0K
描述： IC SENSOR SIGNAL COND 16-SSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,000
類型： 信號調節器
輸入類型： 模擬
輸出類型： 模擬
接口： 串行
電流 - 電源： 2.5mA
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 16-SSOP
包裝： 帶卷 (TR)
MAX1452
Low-Cost Precision Sensor
Signal Conditioner
13
Maxim Integrated
3) Write the load internal calibration register (LdICR)
command to CRIL[3:0].
When a LdICR command is issued to the CRIL register,
the calibration register loaded depends on the address
in the internal calibration register address (ICRA). Table
12 specifies which calibration register is decoded.
Erasing and Writing the EEPROM
The internal EEPROM needs to be erased (bytes set to
FFhex) prior to programming the desired contents.
Remember to save the 3 MSBs of byte 161hex (high-
byte of the configuration register) and restore it when
programming its contents to prevent modification of the
trimmed oscillator frequency.
The internal EEPROM can be entirely erased with the
ERASE command, or partially erased with the
PageErase command (see Table 11, CRIL command).
It is necessary to wait 6ms after issuing the ERASE or
PageErase command.
After the EEPROM bytes have been erased (value of
every byte = FFhex), the user can program its contents,
following the procedure below:
1) Write the 8 data bits to DHR[7:0] using two byte
accesses into the interface register set.
2) Write the address of the target internal EEPROM
location to IEEA[9:0] using three byte accesses into
the interface register set.
3) Write the EEPROM write command (EEPW) to
CRIL[3:0].
Serial Digital Output
When a RdIRS command is written to CRIL[3:0], DIO is
configured as a digital output and the contents of the
register designated by IRSP[3:0] are sent out as a byte
framed by a start bit and a stop bit.
Once the tester finishes sending the RdIRS command,
it must three-state its connection to DIO to allow the
MAX1452 to drive the DIO line. The MAX1452 three-
states DIO high for 1 byte time and then drive with the
start bit in the next bit period followed by the data byte
and stop bit. The sequence is shown in Figure 5.
The data returned on a RdIRS command depends on
the address in IRSP. Table 13 defines what is returned
for the various addresses.
Multiplexed Analog Output
When a RdAlg command is written to CRIL[3:0] the
analog signal designated by ALOC[3:0] is asserted on
the OUT pin. The duration of the analog signal is deter-
mined by ATIM[3:0] after which the pin reverts to three-
state. While the analog signal is asserted in the OUT
pin, DIO is simultaneously three-stated, enabling a par-
allel wiring of DIO and OUT. When DIO and OUT are
connected in parallel, the host computer or calibration
system must three-state its connection to DIO after
asserting the stop bit. Do not load the OUT line when
reading internal signals, such as BDR, FSOTC...etc.
The analog output sequence with DIO and OUT is
shown in Figure 6.
The duration of the analog signal is controlled by
ATIM[3:0] as given in Table 14.
DRIVEN BY TESTER
DRIVEN BY MAX1452
THREE-STATE
NEED WEAK
PULLUP
THREE-STATE
NEED WEAK
PULLUP
START-BIT
LSB
START-BIT
LSB
MSB
STOP-BIT
MSB
STOP-BIT
11 1 1 1 0 1 0 0 11 0 1 0 1 1 111 11 1 1 10 0 0 0 0 1 0 0 0 1 11 1 1 1 1 1 1 11
DIO
Figure 5. DIO Output Data Format
相關PDF資料
PDF描述
MAX1452CAE+TC8H IC SENSOR SIGNAL COND 16SSOP
MAX1452CAE+T IC SENSOR SIGNAL COND 16-SSOP
MAX1452CAE+C8H IC SENSOR SIGNAL COND 16-SSOP
2-221128-3 CONN PLUG BNC 50 OHM CRIMP GOLD
2-221185-9 PLUG,75 OHM,COML BNC
相關代理商/技術參數
參數描述
MAX1452EVKIT-CS 功能描述:數據轉換 IC 開發工具 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1452EVKIT-NS 功能描述:數據轉換 IC 開發工具 Low-Cost Precision Sensor Signal Conditioner RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1452EVKIT-NS+ 功能描述:數據轉換 IC 開發工具 Programmers, Development Systems Eval and Demo Boards and Kits - KIT EVAL MAX1452-NS RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1452KEY 功能描述:溫度傳感器開發工具 MAX1455 Eval Kit RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
MAX14530EEVKIT+ 制造商:Maxim Integrated Products 功能描述:OVERVOLTAGE PROTECTION WITH USB CHARGER DETECTION LDO AND ES - Boxed Product (Development Kits)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*