- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX14523BATA/V+T (Maxim Integrated Products)IC CURRENT LIMIT SWITCH 8TDFN PDF資料下載
參數資料
| 型號： | MAX14523BATA/V+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CURRENT LIMIT SWITCH 8TDFN |
| 標準包裝： | 2,500 |
| 系列： | * |
MAX14523A/MAX14523AL/MAX14523B/MAX14523C
250mA to 1.5A, Adjustable
Current-Limit Switches
8
_______________________________________________________________________________________
Functional Diagram
MAX14523A
MAX14523AL
MAX14523B
MAX14523C
BUFFER
IN
N.C.
THERMAL
SHUTDOWN
CONTROL
LOGIC
REVERSE-
CURRENT
PROTECTION
TIMING
CIRCUITRY
BUFFER
CURRENT
LIMIT
BANDGAP
REFERENCE
OUT
FLAG
SETI
*( ) FOR THE MAX14523AL ONLY
ON/(ON)*
GND
Detailed Description
The MAX14523A/MAX14523AL/MAX14523B/MAX14523C
programmable current-limit switches operate from
+1.7V to +5.5V and provide internal current limiting
adjustable from 250mA to 1.5A. These devices feature
a fixed blanking time, and a FLAG output that notifies
the processor when a fault condition is present.
Programmable Current Limit/Threshold
A resistor from SETI to GND sets the current
limit/threshold for the switch (see the
Setting the
Current Limit/Threshold section). If the output current is
limited at the current threshold value for a time equal to
or longer than tBLANK, the output flag asserts and the
MAX14523A/MAX14523AL enter the autoretry mode,
the MAX14523B latches off the switch, and the
MAX14523C enters the continuous current-limit mode.
Autoretry (MAX14523A/MAX14523AL)
When the forward current reaches the current thresh-
old, the tBLANK timer begins counting (Figure 2). FLAG
asserts if the overcurrent condition is present for
tBLANK or longer. The timer resets if the overcurrent
condition disappears before the blanking time (tBLANK)
has elapsed. A retry time delay (tRETRY) starts immedi-
ately after the blanking time has elapsed. During that
time, the switch latches off. At the end of tRETRY, the
switch turns on again. If the fault still exists, the cycle
repeats. If the fault has been removed, the switch stays
on. During this cycle, FLAG stays low. In autoretry, if
the die temperature exceeds +170°C (typ) due to self
heating, the MAX14523A/MAX14523AL go into thermal
shutdown until the die temperature drops by approxi-
mately 15°C (see the
Thermal Shutdown section.)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1452AAE+T | IC SENSOR SIGNAL COND 16-SSOP |
| MAX14531EEWC+T | IC USB SWITCH DP3T 12WLP |
| MAX14536EEVB+ | IC SWITCH DPDT 10UTQFN |
| MAX1455AUE+T | IC AUTO SNSR SIGNAL COND 16TSSOP |
| MAX14566AEETA+T | IC USB SWITCH HOST CHARGER 8TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14523BETA+ | 制造商:Maxim Integrated Products 功能描述:250MA TO 1.5A, ADJUSTABLE CURRENT-LIMIT SWITCHES - Rail/Tube |
| MAX14523CATA+ | 制造商:Maxim Integrated Products 功能描述:250MA TO 1.5A ADJUSTABLE CURRENT-L - Rail/Tube |
| MAX14523CATA+T | 功能描述:電源開關 IC - 配電 Adjustable Current Limit Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MAX14523EVKIT+ | 功能描述:電源開關 IC - 配電 EVKits RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MAX14525ETA+ | 制造商:Maxim Integrated Products 功能描述:BATTERY SWITCH WITH FOUR ENABLE INP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。