- 您現在的位置：買賣IC網 > PDF目錄10488 > MAX1403EAI+ (Maxim Integrated Products)IC ADC 18BIT LP 28-SSOP PDF資料下載
參數資料
| 型號： | MAX1403EAI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/36頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT LP 28-SSOP |
| 產品培訓模塊： | MAX11200 ADC Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 46 |
| 位數： | 18 |
| 采樣率（每秒）： | 480 |
| 數據接口： | QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 21.45mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 3 個差分，單極；3 個差分，雙極；5 個偽差分，單極；5 個偽差分，雙極 |
| 產品目錄頁面： | 1396 (CN2011-ZH PDF) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MAX1403
+3V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
______________________________________________________________________________________
11
Pin Description
15
AIN5
Analog Input Channel 5. Used as a differential or pseudo-differential input with AIN6 (see On-Chip
Registers section).
NAME
FUNCTION
1
CLKIN
Clock Input. A crystal can be connected across CLKIN and CLKOUT. Alternatively, drive CLKIN with a
CMOS-compatible clock at a nominal frequency of 2.4576MHz or 1.024MHz, and leave CLKOUT uncon-
nected. Frequencies of 4.9152MHz and 2.048MHz may be used if the X2CLK control bit is set to 1.
PIN
2
CLKOUT
Clock Output. When deriving the master clock from a crystal, connect the crystal between CLKIN and
CLKOUT. In this mode, the on-chip clock signal is not available at CLKOUT. Leave CLKOUT unconnected
when CLKIN is driven with an external clock.
3
CS
Chip-Select Input. This active-low logic input is used to enable the digital interface. With CS hard-wired
low, the MAX1403 operates in its 3-wire interface mode with SCLK, DIN, and DOUT used to interface to
the device. CS is used either to select the device in systems with more than one device on the serial bus,
or as a frame-synchronization signal for the MAX1403, when a continuous SCLK is used.
4
RESET
Active-Low Reset Input. Drive low to reset the control logic, interface logic, digital filter, and analog modu-
lator to power-on status. RESET must be high and CLKIN must be toggling in order to exit reset.
5
DS1
Digital Input for Auxiliary Data Input Bit 1. The status of this bit is reflected in the output data by bit D4.
Used to communicate the status of DS1 via the serial interface.
6
DS0
Digital Input for Auxiliary Data Input Bit 0. The status of this bit is reflected in the output data by bit D3.
Used to communicate the status of DS0 via the serial interface.
7
OUT2
Transducer Excitation Current Source 2
8
OUT1
Transducer Excitation Current Source 1
9
AGND
Analog Ground. Reference point for the analog circuitry. AGND connects to the IC substrate.
10
V+
Analog Positive Supply Voltage (+2.7V to +3.6V).
11
AIN1
Analog Input Channel 1. May be used as a pseudo-differential input with AIN6 as common, or as the posi-
tive input of the AIN1/AIN2 differential analog input pair (see On-Chip Registers section).
12
AIN2
Analog Input Channel 2. May be used as a pseudo-differential input with AIN6 as common, or as the neg-
ative input of the AIN1/AIN2 differential analog input pair (see On-Chip Registers section).
13
AIN3
Analog Input Channel 3. May be used as a pseudo-differential input with AIN6 as common, or as the posi-
tive input of the AIN3/AIN4 differential analog input pair (see On-Chip Registers section).
14
AIN4
Analog Input Channel 4. May be used as a pseudo-differential input with AIN6 as common, or as the neg-
ative input of the AIN3/AIN4 differential analog input pair (see On-Chip Registers section).
16
AIN6
Analog Input 6. May be used as a common point for AIN1 through AIN5 in pseudo-differential mode, or as
the negative input of the AIN5/AIN6 differential analog input pair (see On-Chip Registers section).
17
CALGAIN-
Negative Gain Calibration Input. Used for system gain calibration. It forms the negative input of a fully
differential input pair with CALGAIN+. Normally these inputs are connected to reference voltages in the
system. When system gain calibration is not required and the auto-sequence mode is used, the
CALGAIN+/CALGAIN- input pair provides an additional fully differential input channel.
18
CALGAIN+
Positive Gain Calibration Input. Used for system gain calibration. It forms the positive input of a fully
differential input pair with CALGAIN-. Normally these inputs are connected to reference voltages in the
system. When system gain calibration is not required and the auto-sequence mode is used, the
CALGAIN+/CALGAIN- input pair provides an additional fully differential input channel.
相關PDF資料 |
PDF描述 |
|---|---|
| UP050SL130J-A-B | CAP CER 13PF 50V 5% AXIAL |
| VE-B5J-MX-F3 | CONVERTER MOD DC/DC 36V 75W |
| VE-B54-MX-F4 | CONVERTER MOD DC/DC 48V 75W |
| UP050SL120J-NAC | CAP CER 12PF 50V 5% AXIAL |
| UP050SL120J-KFC | CAP CER 12PF 50V 5% AXIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1403EAI+ | 功能描述:模數轉換器 - ADC 18-Bit 5Ch 4.8ksps 1.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1403EAI+T | 功能描述:模數轉換器 - ADC 18-Bit 5Ch 4.8ksps 1.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1403EAI-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1403EVKIT | 功能描述:數據轉換 IC 開發工具 MAX1403 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1403EVL11 | 功能描述:數據轉換 IC 開發工具 MAX1403 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。