參數資料
型號: MAX1359BETL+
廠商: Maxim Integrated Products
文件頁數: 17/71頁
文件大?。?/td> 0K
描述: IC DAS 16BIT 40-TQFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 50
類型: 數據采集系統(DAS)
分辨率(位): 16 b
采樣率(每秒): 21.84k
數據接口: 串行
電壓電源: 模擬和數字
電源電壓: 1.8 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 40-WFQFN 裸露焊盤
供應商設備封裝: 40-TQFN-EP(6x6)
包裝: 管件
MAX1358B
16-Bit, Data-Acquisition System with ADC, DACs,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
24
______________________________________________________________________________________
PIN
NAME
FUNCTION
1
CLK
Clock Output. Default is 2.457MHz output clock for the μC.
2
UPIO2
User-Programmable Input/Output 2. See the UPIO2_CTRL Register section for functionality.
3
UPIO3
User-Programmable Input/Output 3. See the UPIO3_CTRL Register section for functionality.
4
UPIO4
User-Programmable Input/Output 4. See the UPIO4_CTRL Register section for functionality.
5
DOUT
Serial-Data Output. Data is clocked out on SCLK’s falling edge. High impedance when
CS is high, when
UPIO/SPI pass-through mode is enabled, DOUT mirrors the state of UPIO1.
6
SCLK
Serial-Clock Input. Clocks data in and out of the serial interface.
7
DIN
Serial-Data Input. Data is clocked in on SCLK’s rising edge.
8
CS
Active-Low Chip-Select Input. Data is not clocked into DIN unless
CS is low. When CS is high, DOUT is high
impedance. High impedance when
CS is high; when UPIO/SPI pass-through mode is enabled, DOUT
mirrors the state of UPIO1.
9
INT
Programmable Active-High/Low Interrupt Output. ADC, UPIO wake-up, alarm, and voltage-monitor events.
10
CLK32K
32kHz Clock Input/Output. Outputs 32kHz clock for the μC. Can be programmed as an input by enabling
the IO32E bit to accept an external 32kHz input clock. The RTC, PWM, and watchdog timer always use the
internal 32kHz clock derived from the 32kHz crystal.
11
RESET
Active-Low, Open-Drain Reset Output. Remains low while DVDD is below the 1.8V voltage threshold and
stays low for a timeout period (tDSLP) after DVDD rises above the 1.8V threshold.
RESET also pulses low
when the watchdog timer times out and holds low during POR until the 32kHz oscillator stabilizes.
12
32KOUT
32kHz Crystal Output. Connect an external 32kHz watch crystal between 32KIN and 32KOUT.
13
32KIN
32kHz Crystal Input. Connect an external 32kHz watch crystal between 32KIN and 32KOUT.
14
SNO1
Analog Switch 1 Normally Open Terminal. Analog input to mux.
15
SCM1
Analog Switch 1 Common Terminal. Analog input to mux.
16
SNC1
Analog Switch 1 Normally Closed Terminal. Analog input to mux (open on POR).
17
SNO2
Analog Switch 2 Normally Open Terminal. Analog input to mux.
18
SCM2
Analog Switch 2 Common Terminal. Analog input to mux (open on POR).
19
SNC2
Analog Switch 2 Normally Closed Terminal. Analog input to mux.
20
OUT1
Amplifier 1 Output. Analog input to mux.
21
IN1-
Amplifier 1 Inverting Input. Analog input to mux.
22
IN1+
Amplifier 1 Noninverting Input
Pin Description
相關PDF資料
PDF描述
D38999/26WG16PB CONN PLUG 16POS STRAIGHT W/PINS
MAX186CCWP+T IC ADC 12BIT SERIAL 20-SOIC
MS27474T18B28P CONN RCPT 28POS JAM NUT W/PINS
MAX1022BETX+T IC ADC/DAC 10BIT W/FIFO 36-TQFN
MS27505E17F6P CONN RCPT 6POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
MAX1359BETL+ 功能描述:數據轉換系統 16-Bit 2Ch .512ksps 3.6V Precision SoIC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX1359BETL+T 功能描述:數據轉換系統 16-Bit 2Ch .512ksps 3.6V Precision SoIC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX1359BETL-T 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX135C/D 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX135CP1 DC/94 制造商:INT 功能描述:135C