- 您現在的位置：買賣IC網 > PDF目錄9833 > MAX13411EESA+T (Maxim Integrated Products)IC TXRX RS-485 LDO/CTRL 8-SOIC PDF資料下載
參數資料
| 型號： | MAX13411EESA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS-485 LDO/CTRL 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS485 |
| 電源電壓： | 6 V ~ 28 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 8-SO 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Human Body Model
Figure 8a shows the Human Body Model, and Figure
8b shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of inter-
est, which is then discharged into the test device
through a 1.5k
Ω resistor.
Applications Information
Typical Applications
The MAX13410E–MAX13415E transceivers are designed
for half-duplex, bidirectional data communications on
multipoint bus transmission lines. To minimize reflections,
terminate the line at both ends in its characteristic
impedance, and keep stub lengths off the main line as
short as possible. The slew-rate-limited MAX13410E/
MAX13412E/MAX13414E are more tolerant of imperfect
termination.
Typical Application Circuit for the
MAX13410E and MAX13411E
This application circuit shows the MAX13410E/
MAX13411E being used in an isolated application (see
Figure 9). The MAX13410E/MAX13411E use the industry-
standard pin out but do not have a VREG output for
biasing external circuitry. The positive temperature coef-
ficient (PTC) and transient voltage suppressor (TVS)
clamp circuit on the RS-485 outputs are intended to pro-
vide overvoltage fault protection and are optional based
on the requirements of the design.
Typical Application Circuit for the
MAX13412E and MAX13413E
This application circuit shows the MAX13412E and
MAX13413E being used in an isolated application
where the AutoDirection feature is implemented to
reduce the number of optical isolators to two (see
Figure 10). The MAX13412E/MAX13413E provide a
VREG output that can be used to power external circuit-
ry up to 20mA.
Typical Application Circuit for the
MAX13414E and MAX13415E
This application circuit shows the MAX13414E/
MAX13415E being used in an isolated application using
an unregulated power supply with three optical isolators
(see Figure 11). The MAX13414E/MAX13415E provide a
VREG output that can be used to power external circuitry
up to 20mA.
256 Transceivers on the Bus
The RS-485 standard specifies the load each receiver
places on the bus in terms of unit loads. An RS-485-
compliant transmitter can drive 32 one-unit load
receivers when used with a 120
Ω cable that is terminat-
ed on both ends over a -7V to +12V common-mode
range. The MAX13410E–MAX13415E are specified as
1/8 unit loads. This means a compliant transmitter can
drive up to 256 devices of the MAX13410E–MAX13415E.
Reducing the common mode, and/or changing the char-
acteristic impedance of the cable, changes the maxi-
mum number of receivers that can be used. Refer to the
TIA/EIA-485 specification for further details.
Proper Termination and Cabling/
Wiring Configurations
When the data rates for RS-485 are high relative to the
cable length it is driving, the system is subject to proper
MAX13410E–MAX13415E
RS-485 Transceiver with Integrated Low-Dropout
Regulator and AutoDirection Control
______________________________________________________________________________________
19
CHARGE-CURRENT-
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
100pF
RC
1M
Ω
RD
1500
Ω
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 8a. Human Body ESD Test Model
IP 100%
90%
36.8%
tRL
TIME
tDL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
Ir
10%
0
AMPS
Figure 8b. Human Body Current Waveform
相關PDF資料 |
PDF描述 |
|---|---|
| MS27656E13B22P | CONN RCPT 22POS WALL MNT W/PINS |
| MAX13412EESA+T | IC TXRX RS-485 LDO/CTRL 8-SOIC |
| MAX1177BEUP+ | IC ADC 16BIT 135KSPS 20-TSSOP |
| MAX170CCWE+ | IC ADC 12BIT SERIAL 16-SOIC |
| MAX3056ASD+T | IC TXRX CAN FP 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13412EESA+ | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13412EESA+T | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13413EESA+ | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13413EESA+T | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13414EESA+ | 功能描述:RS-485接口IC Ic Txrx RS-485 Ldo/Ctrl RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。