- 您現在的位置：買賣IC網 > PDF目錄10207 > MAX13325GUI/V+ (Maxim Integrated Products)IC AUD LINE DVR DL AUTO 28TSSOP PDF資料下載
參數資料
| 型號： | MAX13325GUI/V+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/21頁 |
| 文件大小： | 0K |
| 描述： | IC AUD LINE DVR DL AUTO 28TSSOP |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 線路驅動器，發射器 |
| 應用： | 車載音頻 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 28-TSSOP 裸露焊盤 |
| 包裝： | 管件 |
16
Maxim Integrated
Dual Automotive, Audio Line Drivers
with I2C Control and Diagnostic
MAX13325/MAX13326
Applications Information
Serial Interface
Writing to the MAX13325/MAX13326 using I2C requires
that first the master sends a START (S) condition fol-
lowed by the device’s I2C address. After the address,
the master sends the register address of the register
that is to be programmed. The master then ends com-
munication by issuing a STOP (P) condition to relinquish
control of the bus, or a Repeated START (Sr) condition to
communicate to another I2C slave (see Figure 1).
Bit Transfer
Each SCL rising edge transfers one data bit. The data
on SDA must remain stable during the high portion of the
SCL clock pulse (see Figure 2). Changes in SDA while
SCL is high are read as control signals (see the START
and STOP Conditions section). When the serial interface
is inactive, SDA and SCL idle high.
Figure 1. I2C Timing
Figure 2. Bit Transfer
Table 17. Overvoltage Diagnostic
tLOW
tF
SDA
SCL
tHD:STA
S
tSU:STA
tHD:DAT
tHIGH
tLOW
tSU:DAT
tF
tHD:STA
tSP
P
tSU:STO
S
Sr
tBUF
tR
SDA
SCL
DATA LINE
STABLE;
DATA VALID
CHANGE OF
DATA ALLOWED
FAULT CONDITION
STATUS REPORT
UNMASK
RECOVERY
Overvoltage
Shutdown
FLAG is asserted low.
In GMASK register, set
MDUMP bit to 1.
See Table 8.
VDD voltage falls below overvoltage
threshold. Cleared on reading the
GFAULT register. Note: 500ms
autoretry in stand-alone mode.
FLAG bit set. See Table 7.
DUMP bit is set in the GFAULT
register. See Table 4.
Left and right channels switch
off and output goes to a
high-impedance state.
Cannot be masked.
Left channel is enabled by setting
the RETRYL bit to 1. Right channel
is enabled by setting the RETRYR
bit to 1. See Table 3.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3100R22-22S | CONN RCPT 4POS WALL MNT W/SCKT |
| MS3106F28-18P | CONN PLUG 12POS STRAIGHT W/PINS |
| MAX5440EAG+T | IC CNTRL VOL STEREO 24-SSOP |
| MS27473T16F8SB | CONN PLUG 8POS STRAIGHT W/SCKT |
| MAX9890AETA+T | IC SUPP CLICK-POP 8-TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13326GUI/V+ | 功能描述:緩沖器和線路驅動器 Dual Audio Line Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MAX13326GUI/V+T | 功能描述:緩沖器和線路驅動器 Dual Audio Line Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MAX13330GEE/V+ | 功能描述:音頻放大器 DirectDrive Head Phone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX13330GEE/V+T | 功能描述:音頻放大器 DirectDrive Head Phone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX13331EVKIT+ | 功能描述:音頻 IC 開發工具 MAX13331 DirectDrive Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。