- 您現在的位置：買賣IC網 > PDF目錄299460 > MAX1300BEUG+ (MAXIM INTEGRATED PRODUCTS INC) 8-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 PDF資料下載
參數資料
| 型號： | MAX1300BEUG+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 8-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 |
| 封裝： | 4.40 MM, ROHS COMPLIANT, MO-153AD, TSSOP-24 |
| 文件頁數： | 18/35頁 |
| 文件大?。?/td> | 1084K |
| 代理商： | MAX1300BEUG+ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
External-Acquisition-Mode Control Byte
Internal-Clock-Mode Control Byte
Reset Byte
Partial Power-Down-Mode Control Byte
This prevents the MAX1300/MAX1301 from inadvertent-
ly exiting full power-down mode because of a CS glitch
in a noisy digital environment.
Power-On Reset
The MAX1300/MAX1301 power up in normal operation
configured for external clock mode with all circuitry
active (Tables 7 and 8). Each analog input channel
(CH0–CH7) is set for single-ended conversions with a
±3 x VREF bipolar input range (Table 6).
Allow the power supplies to stabilize after power-up. Do
not initiate any conversions until the power supplies
have stabilized. Additionally, allow 10ms for the internal
reference to stabilize when CREF = 1.0μF and CREFCAP
= 0.1μF. Larger reference capacitors require longer
stabilization times.
Internal or External Reference
The MAX1300/MAX1301 operate with either an internal or
external reference. The reference voltage impacts the
ADC’s FSR (Figures 12, 13, and 14). An external refer-
ence is recommended if more accuracy is required than
the internal reference provides, and/or multiple converters
require the same reference voltage.
Internal Reference
The MAX1300/MAX1301 contain an internal 4.096V
bandgap reference. This bandgap reference is connect-
ed to REFCAP through a nominal 5k
Ω resistor (Figure 17).
The voltage at REFCAP is buffered creating 4.096V at
REF. When using the internal reference, bypass
REFCAP with a 0.1μF or greater capacitor to AGND1 and
bypass REF with a 1.0μF or greater capacitor to AGND1.
External Reference
For external reference operation, disable the internal
reference and reference buffer by connecting REFCAP
to AVDD1. With AVDD1 connected to REFCAP, REF
becomes a high-impedance input and accepts an
external reference voltage. The MAX1300/MAX1301
can accept an external reference voltage of 4.096V or
less. However, to meet all of the electrical characteristic
specifications, VREF must be > 38V. The MAX1300/
MAX1301 external reference current varies depending
on the applied reference voltage and the operating
mode (see the External Reference Input Current vs.
External Reference Input Voltage in the
Typical
Operating Characteristics).
Applications Information
Noise Reduction
Additional samples can be taken and averaged (over-
sampling) to remove the effect of transition noise on
conversion results. The square root of the number of
samples determines the improvement in performance.
For example, with 2/3LSBRMS (4LSBP-P) transition
noise, 16 (42 = 16) samples must be taken to reduce
the noise to 1LSBP-P.
Interface with 0 to 10V Signals
In industrial control applications, 0 to 10V signaling is
common. For 0 to 10V applications, configure the selected
MAX1300/MAX1301 input channel for the single-ended 0
to 3 x VREF input range (R[2:0] = 110, Table 6). The 0 to
3x VREF range accommodates 0 to 10V where the sig-
nals saturate at approximately 3 x VREF if out of range.
Interface with 4–20mA Signals
Figure 19 illustrates a simple interface between the
MAX1300/MAX1301 and a 4–20mA signal. 4–20mA sig-
naling can be used as a binary switch (4mA represents
a logic-low signal, 20mA represents a logic-high sig-
nal), or for precision communication where currents
between 4mA and 20mA represent intermediate analog
data. For binary switch applications, connect the
4–20mA signal to the MAX1300/MAX1301 with a resis-
tor to ground. For example, a 250
Ω resistor converts
the 4–20mA signal to a 1V to 5V signal. Adjust the
resistor value so the parallel combination of the resistor
and the MAX1300/MAX1301 source impedance is
250
Ω. In this application, select the single-ended 0 to
(3 x VREF)/2 range (R[2:0] = 011, Table 6). For applica-
tions that require precision measurements of continu-
ous analog currents between 4mA and 20mA, use a
buffer to prevent the MAX1300/MAX1301 input from
diverting current from the 4–20mA signal.
MAX1300/MAX1301
8- and 4-Channel, ±3 x VREF Multirange Inputs,
Serial 16-Bit ADCs
______________________________________________________________________________________
25
REF
REFCAP
AGND1
4.096V
BANDGAP
REFERENCE
5k
Ω
1x
SAR
ADC REF
4.096V
1.0
μF
0.1
μF
VRCTH
MAX1300
MAX1301
Figure 17. Internal Reference Operation
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13208EALB-T | UNIDIRECTIONAL, SILICON, TVS DIODE |
| MAX1450CAP+T | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| MAX16049ATN+ | 8-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC56 |
| MAX2042AETP+T | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, QCC20 |
| MAX2042AETP+ | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, QCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1300BEUG+ | 功能描述:模數轉換器 - ADC 16-Bit 8Ch 115ksps 4.136V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1300BEUG+T | 功能描述:模數轉換器 - ADC 16-Bit 8Ch 115ksps 4.136V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1300EVKIT+ | 功能描述:數據轉換 IC 開發工具 MAX1300 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX13013EBT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX13013EBT+T | 功能描述:轉換 - 電壓電平 RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
發布緊急采購，3分鐘左右您將得到回復。