- 您現在的位置：買賣IC網 > PDF目錄17006 > MAX1280EVC16 (Maxim Integrated Products)EVAL KIT FOR MAX1280 PDF資料下載
參數資料
| 型號： | MAX1280EVC16 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL KIT FOR MAX1280 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 400k |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF/2 |
| 在以下條件下的電源（標準）： | 13.75mW @ 400kSPS |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX1280 |
| 已供物品： | 2 板，CD |
MAX1280/MAX1281
400ksps/300ksps, Single-Supply, Low-Power, 8-Channel,
Serial 12-Bit ADCs with Internal Reference
______________________________________________________________________________________
17
Table 4 details the four power modes with the corre-
sponding supply current and operating sections. For
data rates achievable in software power-down modes,
see Power-Down Sequencing section.
Hardware Power-Down
Pulling SHDN low places the converter in hardware
power-down. Unlike software power-down mode, the
conversion is terminated immediately. When returning
to normal operation from SHDN with an external refer-
ence, the MAX1280/MAX1281 can be considered fully
powered-up within 2s of actively pulling SHDN high.
When using the internal reference, the conversion
should be initiated only after the reference has settled;
its recovery time depends on the external bypass
capacitors and shutdown duration.
Power-Down Sequencing
The MAX1280/MAX1281’s automatic power-down
modes can save considerable power when operating at
less than maximum sample rates. Figures 10 and 11
show the average supply current as a function of the
sampling rate.
Using Full Power-Down Mode
Full power-down mode (FULLPD) achieves the lowest
power consumption at up to 1000 conversions per
channel per second. Figure 10a shows the MAX1281’s
power consumption for 1- or 8-channel conversions
using full power-down mode (PD1 = PD0 = 0), with the
internal reference and the maximum clock speed. A
0.01F bypass capacitor plus the internal 17k
refer-
ence resistor at REFADJ forms an RC filter with a 200s
time constant. To achieve full 12-bit accuracy, 10 time
constants or 2ms are required after power-up if the
bypass capacitor is fully discharged between conver-
sions. Waiting this 2ms in FASTPD mode or reduced-
power mode (REDP) instead of full power-down mode
can further reduce power consumption. This is
achieved by using the sequence shown in Figure 12a.
Figure 10b shows the MAX1281’s power consumption
for 1- or 8-channel conversions using FULLPD mode
(PD1 = PD0 = 0), an external reference, and the maxi-
mum clock speed. One dummy conversion to power-up
the device is needed, but no wait-time is necessary to
start the second conversion, thereby achieving lower
power consumption at up to the full sampling rate.
Using Fast Power-Down and
Reduced-Power Modes
FASTPD and REDP modes achieve the lowest power
consumption at speeds close to the maximum sample
rate. Figure 11 shows the MAX1281’s power consump-
tion in FASTPD mode (PD1 = 0, PD0 = 1), REDP mode
(PD1 = 1, PD0 = 0), and (for comparison) normal
operating mode (PD1 = 1, PD0 = 1). The figure shows
0
0.50
0.25
1.00
0.75
1.25
1.50
0.0001
0.01
0.001
0.1
1
10
TIME IN SHUTDOWN (s)
REFERENCE
POWER-UP
DELAY
(ms)
MAX1281
VDD1 = VDD2 = 3.0V
CLOAD = 20pF
CODE = 101010000000
1000
100
10
1
0.1
10
1
100
1k
10k
SAMPLING RATE (sps)
SUPPLY
CURRENT
(
A)
8 CHANNELS
1 CHANNEL
10,000
1000
10
100
1
100
10
1k
10k
100k
SAMPLING RATE (sps)
SUPPLY
CURRENT
(
A)
MAX1281
VDD1 = VDD2 = 3.0V
CLOAD = 20pF
CODE = 101010000000
8 CHANNELS
1 CHANNEL
Figure 9. Reference Power-Up Delay vs. Time in Shutdown
Figure 10a. Average Supply Current vs. Sample Rate (Using
FULLPD and Internal Reference)
Figure 10b. Average Supply Current vs. Sampling Rate (Using
FULLPD and External Reference)
相關PDF資料 |
PDF描述 |
|---|---|
| LGU2G221MELA | CAP ALUM 220UF 400V 20% SNAP |
| MAX1284EVC16 | EVALUATION SYSTEM FOR MAX1284 |
| 381LX682M025J012 | CAP ALUM 6800UF 25V 20% SNAP |
| GEC13DREI-S93 | CONN EDGECARD 26POS .100 EYELET |
| LGU2G181MELC | CAP ALUM 180UF 400V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1280EVKIT | 功能描述:數據轉換 IC 開發工具 MAX1280 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1281BCUP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1281BCUP+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 300ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1281BCUP+T | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 300ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1281BCUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。