- 您現在的位置：買賣IC網 > PDF目錄9706 > MAX1234ETI+T (Maxim Integrated Products)IC CNTRLR TOUCH 28-TQFN PDF資料下載
參數資料
| 型號： | MAX1234ETI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CNTRLR TOUCH 28-TQFN |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 電阻 |
| 觸摸面板接口： | 4 線 |
| 輸入數/鍵： | 1，4 x 4 小鍵盤 |
| 分辨率（位）： | 8，10，12 b |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 數據速率/采樣率 (SPS，BPS)： | 50k |
| 電壓基準： | 內部 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MAX1233/MAX1234
±15kV ESD-Protected Touch-Screen
Controllers Include DAC and Keypad Controller
______________________________________________________________________________________
15
measurement of the auxiliary inputs. Figure 4 shows the
on-chip reference circuitry of the MAX1233/MAX1234.
Set the internal reference voltage by writing to the RFV
bits in the ADC control register (see Tables 4, 5, and 12).
The MAX1233/MAX1234 can accept an external refer-
ence connected to REF for ADC conversion.
External Reference
The MAX1233/MAX1234 can accept an external refer-
ence connected to the REF pin for ADC conversions.
The internal reference should be disabled (RES1 = 1)
when using an external reference. At a conversion rate
of 50ksps, an external reference at REF must deliver up
to 15A of load current and have 50
Ω or less output
impedance. If the external reference has high output
impedance or is noisy, bypass it close to the REF pin
with a 0.1F capacitor.
Selecting Internal or External Reference
Set the type of reference being used by programming
the ADC control register. To select the internal refer-
ence, clock zeros into bits [A/D3:A/D0] and a zero to bit
RES1, as shown in the
Control Registers section. To
change to external reference mode, clock zeros into
bits [A/D3:A/D0] and a one to bit RES1. See Table 13
for more information about selecting an internal or
external reference for the ADC.
Reference Power Modes
Auto Power-Down Mode (RES1 = RES0 = 0)
The MAX1233/MAX1234 are in auto power-down mode
at initial power-up. Set the RES1 and RES0 bits to zero
to use the MAX1233/MAX1234 in the auto power-down
mode. In this mode, the internal reference is normally
off. When a command to perform a battery measure-
ment, temperature measurement, or auxiliary input
measurement is written to the ADC control register, the
device powers on the internal reference, waits for the
internal reference to settle, completes the requested
scan, and powers down the internal reference. The ref-
erence power delay depends upon the ADC resolution
selected (see Table 8). Do not bypass REF with an
external capacitor when performing scans in auto
power-down mode.
Full-Power Mode (RES1 = 0, RES0 = 1)
In the full-power mode, the RES1 bit is set LOW and
RES0 bit is set HIGH. In this mode, the device is pow-
ered up and the internal ADC reference is always ON.
The MAX1233/MAX1234 internal reference remains fully
powered after completing a scan.
Internal Clock
The MAX1233/MAX1234 operate from an internal oscil-
lator, which is accurate to within 20% of the 10MHz
specified clock rate. The internal oscillator controls the
timing of the acquisition, conversion, touch-screen set-
tling, reference power-up, and keypad debounce times.
8-Bit DAC
The MAX1233/MAX1234 have a voltage-output, true 8-bit
monotonic DAC with less than 1LSB integral nonlinearity
error and less than 1LSB differential nonlinearity error. It
requires a supply current of only 150A (typ) and pro-
vides a buffered voltage output. The DAC is at midscale
code at power-up and remains there until a new code is
written to the DAC register. During shutdown, the DAC’s
output is pulled to ground with a 1MΩ load.
The internal DAC can be used in various system applica-
tions such as LCD/TFT-bias control, automatic tuning
(VCO), power amplifier bias control, programmable
threshold levels, and automatic gain control (AGC).
The 8-bit DAC in the MAX1233/MAX1234 employs a
current-steering topology as shown in Figure 5. At the
core of this DAC is a reference voltage-to-current con-
verter (V/I) that generates a reference current. This cur-
rent is mirrored to 255 equally weighted current
sources. DAC switches control the outputs of these cur-
rent mirrors so that only the desired fraction of the total
current-mirror currents is steered to the DAC output.
The current is then converted to a voltage across a
resistor, and the output amplifier buffers this voltage.
DAC Output Voltage
The 8-bit DAC code is binary unipolar with 1LSB =
(VREF/256). The DAC has a full-scale output voltage of
(0.9
× AVDD - 1LSB).
+1.25V
BANDGAP
2x
REF PIN
OPTIONAL
3R
2R
Figure 4. Block Diagram of the Internal Reference
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B4F-MW-F3 | CONVERTER MOD DC/DC 72V 100W |
| V24B3V3M100BF | CONVERTER MOD DC/DC 3.3V 100W |
| MAX11801GTC/V+ | IC TOUCH SCREEN CTRLR LP 12WQFN |
| MC10EL16DR2 | IC RECEIVER ECL DIFF 5V 8SOIC |
| MC100EP17DWR2 | IC RCVR/DRV ECL QUAD DIFF 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1234EVC16 | 功能描述:數據轉換 IC 開發工具 MAX1233/34 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1234EVKIT | 制造商:Maxim Integrated Products 功能描述:+15KV ESD-PROTECTED TOUCH-SCREEN CO - Rail/Tube |
| MAX1236EUA | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1236EUA+ | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 94.4ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1236EUA+T | 功能描述:模數轉換器 - ADC 12-Bit 4Ch 94.4ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。