- 您現在的位置：買賣IC網 > PDF目錄383313 > MAX1204BCPP (MAXIM INTEGRATED PRODUCTS INC) 5v, 8-cHANNEL, sERIAL, 10-bIT adc WITH 3v dIGITAL iNTERFACE PDF資料下載
參數資料
| 型號： | MAX1204BCPP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 5v, 8-cHANNEL, sERIAL, 10-bIT adc WITH 3v dIGITAL iNTERFACE |
| 中文描述： | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP20 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001AE, DIP-20 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 170K |
| 代理商： | MAX1204BCPP |
M
5V, 8-Channel, S erial, 10-Bit ADC
with 3V Digital Interfac e
10
______________________________________________________________________________________
Input Bandwidth
The ADC’s input tracking circuitry has a 4.5MHz
small-signal bandwidth. Therefore, it is possible to digi-
tize high-speed transient events and measure periodic
signals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Input Range and Input Protec tion
Internal protection diodes, which clamp the analog
inputs to V
DD
and V
SS
, allow the analog input pins to
swing from (V
SS
- 0.3V) to (V
DD
+ 0.3V) without dam-
age. However, for accurate conversions near full scale,
the inputs must not exceed V
DD
by more than 50mV, or
be lower than V
SS
by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off-channels over 2mA, as excessive current
degrades on-channel conversion accuracy.
The full-scale input voltage depends on the voltage at
REF (Tables 1a and 1b).
Quic k Look
Use the circuit of Figure 5 to quickly evaluate the
MAX1204’s analog performance. The MAX1204 requires
that a control byte be written to DIN before each conver-
sion. Tying DIN to +3V feeds in control byte $FF hex,
which triggers single-ended unipolar conversions on
CH7 in external clock mode without powering down
between conversions. In external clock mode, the
SSTRB output pulses high for one clock period before
the most significant bit of the conversion result shifts out
of DOUT. Varying the analog input to CH7 alters the
sequence of bits from DOUT. A total of 15 clock cycles
per conversion is required. All SSTRB and DOUT output
transitions occur on SCLK’s falling edge.
How to S tart a Conversion
Clocking a control byte into DIN starts conversion on
the MAX1204. With
CS
low, each rising edge on SCLK
clocks a bit from DIN into the MAX1204’s internal shift
register. After
CS
falls, the first logic “1” bit defines the
control byte’s MSB. Until this first “start” bit arrives, any
number of logic “0” bits can be clocked into DIN with
no effect. Table 2 shows the control-byte format.
The MAX1204 is fully compatible with Microwire and SPI
devices. For SPI, select the correct clock polarity and
sampling edge in the SPI control registers: set CPOL =
0 and CPHA = 0. Microwire and SPI both transmit a byte
and receive a byte at the same time. Using the Typical
Operating Circuit the simplest software interface
requires only three 8-bit transfers to perform a con-
version (one 8-bit transfer to configure the ADC, and two
more 8-bit transfers to clock out the conversion result).
Table 1b. Bipolar Full Scale, Zero Scale,
and Negative Full Scale
Table 1a. Unipolar Full Scale
and Zero Scale
REFERENCE
External
ZERO
SCALE
0V
0V
0V
Internal
at REFADJ
at REF
FULL SCALE
+4.096V
V
REFADJ
x 1.68
V
REF
REFERENCE
-1/2 V
REF
-1/2 V
REFADJ
x
1.68
-4.096V/2
NEGATIVE
FULL SCALE
ZERO
SCALE
0V
0V
0V
Internal
at
REFADJ
at REF
FULL SCALE
+4.096V / 2
+1/2 V
REFADJ
x 1.68
+1/2 V
REF
External
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1205 | +5v sINGLE-sUPPLY, 1mSPS, 14-bIT sELF-cALIBRATING adc |
| MAX1205EMH | +5v sINGLE-sUPPLY, 1mSPS, 14-bIT sELF-cALIBRATING adc |
| MAX1205CMH | +5v sINGLE-sUPPLY, 1mSPS, 14-bIT sELF-cALIBRATING adc |
| MAX121EAP | 308Ksps ADC with DSP Interface and 78dB SINAD |
| MAX121EWE | 308Ksps ADC with DSP Interface and 78dB SINAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1204BCPP+ | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1204BEAP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1204BEAP+ | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1204BEAP+T | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1204BEAP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。