- 您現在的位置：買賣IC網 > PDF目錄2008 > MAX1184ECM+TD (Maxim Integrated Products)IC ADC 10BIT 20MSPS DL 48-TQFP PDF資料下載
參數資料
| 型號： | MAX1184ECM+TD |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 20MSPS DL 48-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 位數： | 10 |
| 采樣率（每秒）： | 20M |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 150mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP 裸露焊盤 |
| 供應商設備封裝： | 48-TQFP 裸露焊盤（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，雙極；2 個差分，雙極 |
MAX1184
Dual 10-Bit, 20Msps, 3V, Low-Power ADC with
Internal Reference and Parallel Outputs
______________________________________________________________________________________
17
Typical QAM Demodulation Application
The most frequently used modulation technique for digi-
tal communications applications is probably the quadra-
ture amplitude modulation (QAM). Typically found in
spread-spectrum-based systems, a QAM signal repre-
sents a carrier frequency modulated in both amplitude
and phase. At the transmitter, modulating the baseband
signal with quadrature outputs, a local oscillator followed
by subsequent up-conversion can generate the QAM
signal. The result is an in-phase (I) and a quadrature (Q)
carrier component, where the Q component is 90 degree
phase-shifted with respect to the in-phase component. At
the receiver, the QAM signal is divided down into it’s I
and Q components, essentially representing the modula-
tion process reversed. Figure 8 displays the demodula-
tion process performed in the analog domain, using the
dual matched 3V, 10-bit ADC (MAX1184), and the
MAX2451 quadrature demodulator to recover and digi-
tize the I and Q baseband signals. Before being digitized
by the MAX1184, the mixed down-signal components
may be filtered by matched analog filters, such as
Nyquist or pulse-shaping filters, which remove any
unwanted images from the mixing process, thereby
enhancing the overall signal-to-noise (SNR) performance
and minimizing intersymbol interference.
Grounding, Bypassing, and
Board Layout
The MAX1184 requires high-speed board layout design
techniques. Locate all bypass capacitors as close to the
device as possible, preferably on the same side as the
ADC, using surface-mount devices for minimum induc-
tance. Bypass VDD, REFP, REFN, and COM with two
parallel 0.1F ceramic capacitors and a 2.2F bipolar
capacitor to GND. Follow the same rules to bypass the
digital supply (OVDD) to OGND. Multilayer boards with
separated ground and power planes produce the high-
est level of signal integrity. Consider the use of a split
ground plane arranged to match the physical location of
the analog ground (GND) and the digital output driver
ground (OGND) on the ADC’s package. The two ground
planes should be joined at a single point such that the
noisy digital ground currents do not interfere with the
analog ground plane. The ideal location of this connec-
tion can be determined experimentally at a point along
the gap between the two ground planes, which pro-
duces optimum results. Make this connection with a low-
value, surface-mount resistor (1
to 5), a ferrite bead,
or a direct short. Alternatively, all ground pins could
share the same ground plane, if the ground plane is suf-
ficiently isolated from any noisy, digital systems ground
plane (e.g., downstream output buffer or DSP ground
plane). Route high-speed digital signal traces away
from the sensitive analog traces of either channel. Make
sure to isolate the analog input lines to each respective
converter to minimize channel-to-channel crosstalk.
Keep all signal lines short and free of 90 degree turns.
Static Parameter Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from a straight line. This straight
line can be either a best straight-line fit or a line drawn
between the endpoints of the transfer function, once
offset and gain errors have been nullified. The static lin-
earity parameters for the MAX1184 are measured using
the best straight-line fit method.
0
°
90
°
÷8
DOWNCONVERTER
MAX2451
INA+
MAX1184
INA-
INB+
INB-
DSP
POST
PROCESSING
Figure 8. Typical QAM Application, Using the MAX1184
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1186ECM+TD | IC ADC 10BIT 40MSPS DL 48-TQFP |
| MAX1187CCUI+ | IC ADC 16BIT 135KSPS 28-TSSOP |
| MAX118EAI+ | IC ADC 8BIT 1MSPS 28-SSOP |
| MAX1191ETI+T | IC ADC 8BIT 7.5MSPS DL 28-TQFN |
| MAX1192ETI+T | IC ADC 8BIT 22MSPS DL 28-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11850ETM+ | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11850ETM+T | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11850GTM+ | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11850GTM+T | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11850HTEVS+ | 功能描述:數據轉換 IC 開發工具 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。