參數資料
型號: MAX1182
廠商: Maxim Integrated Products, Inc.
英文描述: Dual 10-Bit, 65Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs
中文描述: 雙路、10位、65Msps、+3V、低功耗ADC,內置電壓基準,并行輸出
文件頁數: 14/22頁
文件大?。?/td> 684K
代理商: MAX1182
M
Dual 10-Bit, 65Msps, +3V, Low-Power ADC with
Internal Reference and Parallel Outputs
14
______________________________________________________________________________________
Applications Information
Figure 5 depicts a typical application circuit containing
two single-ended to differential converters. The internal
reference provides a V
DD
/2 output voltage for level
shifting purposes. The input is buffered and then split to
a voltage follower and inverter. One lowpass filter per
ADC suppresses some of the wideband noise associat-
ed with high-speed operational amplifiers, follows the
amplifiers. The user may select the R
ISO
and C
IN
val-
ues to optimize the filter performance, to suit a particu-
lar application. For the application in Figure 5, a R
ISO
of
50
is placed before the capacitive load to prevent
ringing and oscillation. The 22pF C
IN
capacitor acts as
a small bypassing capacitor.
Using Transformer Coupling
A RF transformer (Figure 6) provides an excellent solu-
tion to convert a single-ended source signal to a fully
differential signal, required by the MAX1182 for opti-
mum performance. Connecting the center tap of the
transformer to COM provides a V
DD
/2 DC level shift to
the input. Although a 1:1 transformer is shown, a step-
up transformer may be selected to reduce the drive
requirements. A reduced signal swing from the input
driver, such as an op amp, may also improve the over-
all distortion.
In general, the MAX1182 provides better SFDR and
THD with fully-differential input signals than single-
ended drive, especially for very high input frequencies.
In differential input mode, even-order harmonics are
lower as both inputs (INA+, INA- and/or INB+, INB-) are
balanced, and each of the ADC inputs only requires
half the signal swing compared to single-ended mode.
N - 6
N
N - 5
N + 1
N - 4
N + 2
N - 3
N + 3
N - 2
N + 4
N - 1
N + 5
N
N + 6
N + 1
5 CLOCK-CYCLE LATENCY
ANALOG INPUT
CLOCK INPUT
DATA OUTPUT
D9A
D0A
t
D0
t
CH
t
CL
N - 6
N - 5
N - 4
N - 3
N - 2
N - 1
N
N + 1
DATA OUTPUT
D9B
D0B
OUTPUT
D9A
D0A
OE
t
DISABLE
t
ENABLE
HIGH-Z
HIGH-Z
VALID DATA
OUTPUT
D9B
D0B
HIGH-Z
HIGH-Z
VALID DATA
Figure 3. System Timing Diagram
Figure 4. Output Timing Diagram
相關PDF資料
PDF描述
MAX1183 Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs
MAX1183ECM Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs
MAX1185 Dual 10-Bit, 20Msps, +3V, Low-Power ADC with Internal Reference and Multiplexed Parallel Outputs
MAX1185ECM Dual 10-Bit, 20Msps, +3V, Low-Power ADC with Internal Reference and Multiplexed Parallel Outputs
MAX1190 Dual 10-Bit, 120Msps, 3.3V, Low-Power ADC with Internal Reference and Parallel Outputs
相關代理商/技術參數
參數描述
MAX1182ECM 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1182ECM+D 功能描述:模數轉換器 - ADC 10-Bit 2Ch 65Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1182ECM+TD 功能描述:模數轉換器 - ADC 10-Bit 2Ch 65Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1182ECM-D 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1182ECM-T 制造商:Maxim Integrated Products 功能描述:- Tape and Reel