- 您現在的位置：買賣IC網 > PDF目錄2086 > MAX1181ECM+TD (Maxim Integrated Products)IC ADC 10BIT 80MSPS DL 48-TQFP PDF資料下載
參數資料
| 型號： | MAX1181ECM+TD |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 80MSPS DL 48-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 位數： | 10 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 291mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP 裸露焊盤 |
| 供應商設備封裝： | 48-TQFP 裸露焊盤（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，雙極；2 個差分，雙極 |
For stability and noise filtering purposes, bypass REFIN
with a > 10nF capacitor to GND. In internal reference
mode, REFOUT, COM, REFP, and REFN become low-
impedance outputs.
In the buffered external reference mode, adjust the ref-
erence voltage levels externally by applying a stable
and accurate voltage at REFIN. In this mode, COM,
REFP, and REFN become outputs. REFOUT may be left
open or connected to REFIN through a > 10k
Ω resistor.
In the unbuffered external reference mode, connect
REFIN to GND. This deactivates the on-chip reference
buffers for REFP, COM, and REFN. With their buffers
shut down, these nodes become high impedance and
may be driven through separate external reference
sources.
Clock Input (CLK)
The MAX1181’s CLK input accepts CMOS-compatible
clock signals. Since the interstage conversion of the
device depends on the repeatability of the rising and
falling edges of the external clock, use a clock with low
jitter and fast rise and fall times (< 2ns). In particular,
sampling occurs on the rising edge of the clock signal,
requiring this edge to provide lowest possible jitter. Any
significant aperture jitter would limit the SNR perfor-
mance of the on-chip ADCs as follows:
SNR = 20 log10 (1 / [2
π x fIN tAJ]),
where fIN represents the analog input frequency and
tAJ is the time of the aperture jitter.
Clock jitter is especially critical for undersampling
applications. The clock input should always be consid-
ered as an analog input and routed away from any ana-
log input or other digital signal lines.
The MAX1181 clock input operates with a voltage thresh-
old set to VDD / 2. Clock inputs with a duty cycle other
than 50% must meet the specifications for high and low
periods as stated in the Electrical Characteristics table.
System Timing Requirements
Figure 3 depicts the relationship between the clock
input, analog input, and data output. The MAX1181
samples at the rising edge of the input clock. Output
data for channels A and B is valid on the next rising
edge of the input clock. The output data has an internal
latency of five clock cycles. Figure 4 also determines
the relationship between the input clock parameters
and the valid output data on channels A and B.
Digital Output Data, Output Data Format
Selection (T/B), Output Enable (
OE)
All digital outputs, D0A–D9A (Channel A) and D0B–D9B
(Channel B), are TTL/CMOS logic-compatible. There is a
MAX1181
Dual 10-Bit, 80Msps, 3V, Low-Power ADC
with Internal Reference and Parallel Outputs
______________________________________________________________________________________
11
T/H
VOUT
x2
Σ
FLASH
ADC
DAC
1.5 BITS
10
VINA
VIN
STAGE 1
STAGE 2
D9A–D0A
VINA = INPUT VOLTAGE BETWEEN INA+ AND INA- (DIFFERENTIAL OR SINGLE-ENDED)
VINB = INPUT VOLTAGE BETWEEN INB+ AND INB- (DIFFERENTIAL OR SINGLE-ENDED)
DIGITAL CORRECTION LOGIC
STAGE 8
STAGE 9
2-BIT FLASH
ADC
T/H
VOUT
x2
Σ
FLASH
ADC
DAC
1.5 BITS
10
VINB
VIN
STAGE 1
STAGE 2
D9B–D0B
DIGITAL CORRECTION LOGIC
STAGE 8
STAGE 9
2-BIT FLASH
ADC
T/H
Figure 1. Pipelined Architecture––Stage Blocks
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1182ECM+TD | IC ADC 10BIT 65MSPS DL 48-TQFP |
| MAX1185ECM+D | IC ADC 10BIT 20MSPS DUAL 48-TQFP |
| MAX1188AEUP+ | IC ADC 16BIT 135KSPS 20-TSSOP |
| MAX1193ETI+ | IC ADC 8BIT 45MSPS DUAL 28-TQFN |
| MAX1196ECM+TD | IC ADC 8BIT 40MSPS DL 48-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1181EVKIT | 功能描述:電源管理IC開發工具 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX1182ECM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1182ECM+D | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 65Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1182ECM+TD | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 65Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1182ECM-D | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。