- 您現在的位置：買賣IC網 > PDF目錄383311 > MAX116 (Maxim Integrated Products, Inc.) 2x4-Channel, Simultaneous-Sampling 12-Bit ADCs PDF資料下載
參數資料
| 型號： | MAX116 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 2x4-Channel, Simultaneous-Sampling 12-Bit ADCs |
| 中文描述： | 2x4通道、同時采樣、12位ADC |
| 文件頁數： | 13/14頁 |
| 文件大小： | 215K |
| 代理商： | MAX116 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁
M
2x4-Channel, Simultaneous-Sampling
12-Bit ADCs
______________________________________________________________________________________
13
part of the current (torque) feedback loop. The
MAX115/MAX116 digitize the currents and deliver raw
data to the following DSP and controller stages, where
the vector processing takes place. Sensorless vector
control uses a computer model for the motor and an
algorithm to split each output current into its magnetiz-
ing (stator current) and torque-producing (rotor current)
components.
If a two-to-three phase conversion is not practical,
three currents can be sampled simultaneously with the
addition of a third sensor (not shown). Optional voltage
(position) feedback can be derived by measuring two
phase voltages (CH3A, CH4A). Typically, an isolated
differential amplifier is used between the motor and the
MAX115/MAX116. Again, the third phase voltage can
be derived from the magnitude (phase voltage) and its
relative phase.
For optimum speed control and good load regulation
close to zero speed, additional velocity and position
feedback are derived from an encoder or resolver and
brought to the MAX115/MAX116 at CH4B. The addi-
tional channels can be used to evaluate slower analog
inputs, such as the main DC bus voltage (CH2B), tem-
perature sensors (CH3B), or other analog inputs (AUX,
CH1B).
Power-Supply Bypassing
and Ground Management
For optimum system performance, use printed circuit
boards with separate analog and digital ground planes.
Wire-wrapped boards are not recommended. Connect
the two ground planes together at the low-impedance
power-supply source. For the best ground connection,
connect the DGND and AGND pins together and con-
nect that point to the system analog ground plane to
avoid interference from other digital noise sources. If
DGND is connected to the system digital ground, digi-
tal noise may get through to the ADC’s analog portion.
The AGND pins must be connected directly to a low-
impedance ground plane. Extra impedance between
the pins and the ground plane increases crosstalk and
degrades INL.
MAIN DC
12 BIT ADC +
MICRO-
SEQUENCER
CH1
CH2
CH3
CH4
A
B
A
B
TEMP
A
B
A
B
AUX
MAIN DC
C
F
V
F
VELOCITY
FEEDBACK
AC
AC
MOTOR
S
MAX115
MAX116
R/E
RESOLVER/
ENCODER
μ
C
DSP
12
B
POWER
STAGE
CONTROLLER
EXTERNAL
SETPOINTS
Figure 10. Vector Motor Control
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1160ACPI | 10-Bit, 20Msps, TTL-Output ADC |
| MAX1160 | Low-Voltage Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85 |
| MAX1160ACWI | 10-Bit, 20Msps, TTL-Output ADC |
| MAX1160BCPI | 10-Bit, 20Msps, TTL-Output ADC |
| MAX1160BCWI | 10-Bit, 20Msps, TTL-Output ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1160 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit, 20Msps, TTL-Output ADC |
| MAX11600 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX11600_10 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Evaluation System |
| MAX11600EKA+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX11600EKA+T | 功能描述:模數轉換器 - ADC 8-Bit 4Ch 188ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。