- 您現在的位置：買賣IC網 > PDF目錄17005 > MAX11635EVSYS# (Maxim Integrated Products)KIT EVAL SYSTEM PDF資料下載
參數資料
| 型號： | MAX11635EVSYS# |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/22頁 |
| 文件大小： | 0K |
| 描述： | KIT EVAL SYSTEM |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 300k |
| 數據接口： | SPI? |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | MAX11635 |
| 已供物品： | 板 |
MAX1227/MAX1229/MAX1231
12-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
12
______________________________________________________________________________________
Applications Information
Register Descriptions
The MAX1227/MAX1229/MAX1231 communicate
between the internal registers and the external circuitry
through the SPI-/QSPI-compatible serial interface.
Table 1 details the registers and the bit names. Tables
2–7 show the various functions within the conversion
register, setup register, averaging register, reset regis-
ter, unipolar register, and bipolar register.
Conversion Time Calculations
The conversion time for each scan is based on a num-
ber of different factors: conversion time per sample,
samples per result, results per scan, if a temperature
measurement is requested, and if the external refer-
ence is in use.
Use the following formula to calculate the total conver-
sion time for an internally timed conversion in clock
modes 00 and 10 (see the
Electrical Characteristics
section as applicable):
total conversion time = tcnv x navg x nresult + tTS + tRP
where:
tcnv = tacq(max) + tconv(max)
navg = samples per result (amount of averaging)
nresult = number of FIFO results requested; determined
by number of channels being scanned or by NSCAN1,
NSCAN0
tTS = time required for temperature measurement; set
to zero if temp measurement is not requested
tRP = internal reference wake up; set to zero if internal
reference is already powered up or external reference
is being used
In clock mode 01, the total conversion time depends on
how long CNVST is held low or high, including any time
required to turn on the internal reference. Conversion
time in externally clocked mode (CKSEL1, CKSEL0 = 11)
depends on the SCLK period and how long CS is held
high between each set of eight SCLK cycles. In clock
mode 01, the total conversion time does not include the
time required to turn on the internal reference.
Conversion Register
Select active analog input channels, scan modes, and
a single temperature measurement per scan by writing
to the conversion register. Table 2 details channel
selection, the four scan modes, and how to request a
temperature measurement. Request a scan by writing
to the conversion register when in clock mode 10 or 11,
or by applying a low pulse to the CNVST pin when in
clock mode 00 or 01.
A conversion is not performed if it is requested on a
channel that has been configured as CNVST or REF-.
Do not request conversions on channels 8–15 on the
MAX1227 and channels 12–15 on the MAX1229. Set
CHSEL3:CHSELO to the lower channel’s binary value. If
the last two channels are configured as a differential
pair and one of them has been reconfigured as CNVST
or REF-, the pair is ignored.
Select scan mode 00 or 01 to return one result per sin-
gle-ended channel and one result per differential pair
within the requested range, plus one temperature result if
selected. Select scan mode 10 to scan a single input
channel numerous times, depending on NSCAN1 and
NSCAN0 in the averaging register (Table 6). Select scan
mode 11 to return only one result from a single channel.
Setup Register
Write a byte to the setup register to configure the clock,
reference, and power-down modes. Table 3 details the
REGISTER NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Conversion
1
CHSEL3
CHSEL2
CHSEL1
CHSEL0
SCAN1
SCAN0
TEMP
Setup
0
1
CKSEL1
CKSEL0
REFSEL1
REFSEL0
DIFFSEL1
DIFFSEL0
Averaging
0
1
AVGON
NAVG1
NAVG0
NSCAN1
NSCAN0
Reset
0001
RESET
XX
X
Unipolar mode (setup)
UCH0/1
UCH2/3
UCH4/5
UCH6/7
UCH8/9*
UCH10/11 UCH12/138** UCH14/15**
Bipolar mode (setup)
BCH0/1
BCH1/2
BCH4/5
BCH6/7
BCH8/9*
BCH10/11
BCH12/13** BCH14/15**
Table 1. Input Data Byte (MSB First)
*Unipolar/bipolar channels 8–15 are only valid on the MAX1229 and MAX1231.
*Unipolar/bipolar channels 12–15 are only valid on the MAX1231.
X = Don’t care.
相關PDF資料 |
PDF描述 |
|---|---|
| ADR434BRZ-REEL7 | IC VREF SERIES PREC 4.096V 8SOIC |
| MAX1231BEVSYS# | EVALUATION SYSTEM FOR 12BIT ADC |
| ADR433BRZ-REEL7 | IC VREF SERIES PREC 3V 8-SOIC |
| VI-JWF-EY | CONVERTER MOD DC/DC 72V 50W |
| 0210490308 | CABLE JUMPER 1.25MM .127M 24POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11635EVSYS# | 功能描述:數據轉換 IC 開發工具 MAX11635 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX11636 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:12-Bit, 300ksps ADCs with Differential |
| MAX11636EEE+ | 功能描述:模數轉換器 - ADC 8Ch 12-Bit 300ksps w/FIFO & Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11636EEE+T | 功能描述:模數轉換器 - ADC 8Ch 12-Bit 300ksps w/FIFO & Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11637 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:12-Bit, 300ksps ADCs with Differential |
發布緊急采購，3分鐘左右您將得到回復。