參數資料
型號: MAX115EVKIT
廠商: Maxim Integrated Products
文件頁數: 10/14頁
文件大?。?/td> 0K
描述: EVAL KIT FOR MAX115
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
ADC 的數量: 1
位數: 12
采樣率(每秒): 116k
數據接口: 并聯
輸入范圍: ±5 V
在以下條件下的電源(標準): 17mW @ 116kSPS
工作溫度: 0°C ~ 70°C
已用 IC / 零件: MAX115
已供物品: 板,CD
MAX115/MAX116
2x4-Channel, Simultaneous-Sampling
12-Bit ADCs
_______________________________________________________________________________________
5
CONDITIONS
UNITS
MIN
TYP
MAX
SYMBOL
PARAMETER
TIMING CHARACTERISTICS (continued)
(See Figure 4, AVDD = +5V, AVSS = -5V, DVDD = +5V, AGND = DGND = 0, TA = TMIN to TMAX, Typical values are at TA = +25°C,
unless otherwise noted.)
Mode 1, Channel 1
s
2
Mode 2, Channel 2
4
Mode 3, Channel 3
6
Mode 4, Channel 4
8
tCONV
Exiting shutdown
ms
20
Startup Time
Note 1:
AVDD = +5V, AVSS = -5V, DVDD = +5V, VREFIN = 2.500V (external), VIN = ±5V (MAX115) or ±2.5V (MAX116).
Note 2:
Integral nonlinearity is the analog value’s deviation at any code from its theoretical value after the full-scale range and
offset have been calibrated.
Note 3:
CLK synchronized with CONVST.
Note 4:
fIN = 10.06kHz, VIN = ±5V (MAX115) or ±2.5V (MAX116).
Note 5:
First five harmonics.
Note 6:
All inputs except CH1A driven with ±5V (MAX115) or ±2.5V (MAX116) 10.06kHz signal, CH1A connected to AGND and digi-
tized.
Note 7:
AVDD = DVDD = +5V, AVSS = -5V, VIN = 0V (all channels).
Note 8:
Temperature drift is defined as the change in output voltage from +25°C to TMIN or TMAX. It is calculated as
TC = [
REFOUT/REFOUT] / T.
Note 9:
See Figure 2.
Note 10: Defined as the change in positive full scale caused by a ±5% variation in the nominal supply voltage. Tested with one input
at full scale and all others at AGND. VREFIN = +2.5V (internal).
Note 11: Tested with all inputs connected to AGND. VREFIN = +2.5V (internal).
Note 12: The data access time is defined as the time required for an output to cross +0.8V or +2.0V. It is measured using the circuit
of Figure 1. The measured number is then extrapolated back to determine the value with a 25pF load.
Note 13: The bus relinquish time is derived from the measured time taken for the data outputs to change +0.5V when loaded with the
circuit of Figure 1. The measured number is then extrapolated back to remove the effects of charging and discharging the
120pF capacitor. The time given is the part’s true bus relinquish time, which is independent of the external bus loading capac-
itance.
Conversion Time
Mode 1, Channel 1
ksps
390
Conversion Rate
Mode 2, Channel 2
218
Mode 3, Channel 3
152
Mode 4, Channel 4
116
相關PDF資料
PDF描述
PCM18XD1 MODULE PIC18F248/258/448/458
LGN2H101MELB25 CAP ALUM 100UF 500V 20% SNAP
GSC13DREI CONN EDGECARD 26POS .100 EYELET
MAX117EVKIT-DIP EVAL KIT FOR MAX117
VE-B2Z-EW CONVERTER MOD DC/DC 2V 40W
相關代理商/技術參數
參數描述
MAX115-MAX116 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2x4-Channel, Simultaneous-Sampling 12-Bit ADCs
MAX116 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2x4-Channel, Simultaneous-Sampling 12-Bit ADCs
MAX1160 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit, 20Msps, TTL-Output ADC
MAX11600 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs
MAX11600_10 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Evaluation System