with Internal Temperature Sensor and VDD
參數資料
型號： MAX1153BEUE+T
廠商： Maxim Integrated Products
文件頁數： 17/30頁
文件大小： 0K
描述： IC ADC 10BIT SYS MON 16TSSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
位數： 10
采樣率（每秒）： 94k
數據接口： MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 6.6mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 帶卷 (TR)
輸入數目和類型： 8 個單端，單極；4 個差分，單極；4 個差分，雙極
MAX1153/MAX1154
Stand-Alone, 10-Channel, 10-Bit System Monitors
with Internal Temperature Sensor and VDD Monitor
24
______________________________________________________________________________________
where:
VHIGH = sensor-diode voltage with high current flowing
(IHIGH)
VLOW = sensor-diode voltage with low current flowing
(ILOW)
q = charge of electron = 1.602 10-19 coulombs
k = Boltzman constant = 1.38 10-23 J/K
n = ideality factor (slightly greater than 1)
The temperature measurement process is fully auto-
mated in the MAX1153/MAX1154. All steps are
sequenced and executed by the MAX1153/MAX1154
each time an input channel (or an input channel pair)
configured for temperature measurement is scanned.
The resulting 10-bit, two’s complement number repre-
sents the sensor temperature in degrees Celsius, with
1 LSB = +0.5
°C.
The MAX1153/MAX1154 support both single-ended
and differential temperature measurements.
Applications Information
Setting Up the
MAX1153/MAX1154 Subsystem
The MAX1153/MAX1154 are autonomous subsystems,
requiring only initialization to scan, convert, and monitor
the voltage signals or the temperature sensors con-
nected to their input channels.
For simple applications, using any number of the input
channels and any combination of voltage/temperature
and unipolar/differential, with no interrupt generation
required, use the following intitialization procedure:
Issue a Write Global Configuration Registers com-
mand. This is a single, 5-byte write operation that
configures the input channels, enables the chan-
nels to be used, sets the sample wait time between
scans, configures the interrupt output INT, selects
the reference mode, and starts the automatic scan
mode. See the Write Global Configuration Registers
Command section, Table 2, and Tables 5–10.
Immediately after the global configuration register is
loaded, the MAX1153/MAX1154 begin to update the
current data registers. Acquire conversion data from
the MAX1153/MAX1154 by issuing a command to read
a specific channel with the Read Current Data Register
for Selected Channel command. Read all current data
register at once with the Read Current Data Registers
for All Channels command.
For more complex applications, the monitoring and
interrupt generation features of the MAX1153/MAX1154
require a second step of initialization. Each enabled
channel to be monitored requires configuration using a
Write Configuration Register for Selected Channel com-
mand. Each command is a 5-byte write that sets the
upper and lower fault thresholds, the number of faults for
an alarm before an interrupt is generated, and an aver-
age algorithm parameter if the application requires input
signal filtering.
Applications can read the current data registers and
respond to interrupts signaled by the INT output (see
the
Servicing Interrupts at INT section).
All the MAX1153/MAX1154 registers can be verified by
reading back written data, including the configuration
registers. This feature is useful for development and
testing (see Table 2).
Power-Up/Reset Defaults Summary
Setup Register Power-Up/Reset Defaults
At initial power-up or after a RESET command, the
setup register resets to 00 hex. Consequently, the
MAX1153/MAX1154 are configured as follows:
Sample wait time is 0s.
INT output is open drain and outputs an active-low
signal to signify an alarm.
Table 15. Power-Up/Reset Defaults Summary
REGISTER
BIT RANGE
POWER-UP/RESET STATE
COMMENT
Setup
B0 to B7
All 0s
See Setup Register Power-Up/Reset Defaults
Channel enable
B0 to B11
All 1s
All channels (int/ext) enabled
Input configuration
B0 to B11
All 0s
All single-ended voltage inputs
Alarm register
B0 to B23
All 0s
No alarms set
Channel configuration
B0 to B7
All 0s
Faults = 0, no averaging
Upper threshold
B0 to B9
All 1s
All upper thresholds max range
Lower threshold
B0 to B9
All 0s
All lower thresholds min range
Current data registers
B0 to B9
200hex
Set at midrange
相關PDF資料
PDF描述
MAX1158AEUP+ IC ADC 14BIT 135KSPS 20-TSSOP
MAX11621EEE+T IC ADC 10BIT 4CH 16QSOP
MAX11633EEG+ ADC 12BIT 300KSPS 16CH 24-QSOP
MAX11666AUB/V+ IC ADC 12BIT SRL 500KSPS 10UMAX
MAX1169CEUD+T IC ADC 16BIT 58.6KSPS 14-TSSOP
相關代理商/技術參數
參數描述
MAX1153-MAX1154 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor
MAX1154 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor
MAX1154AEUE 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1154AEUE+ 功能描述:模數轉換器 - ADC HQ PN TESTED 16-TSSOP 173 MIL RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1154AEUE+T 功能描述:模數轉換器 - ADC NULL RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*