- 您現在的位置：買賣IC網 > PDF目錄385520 > MAX1126 (Maxim Integrated Products, Inc.) Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs PDF資料下載
參數資料
| 型號： | MAX1126 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs |
| 中文描述： | 四路、12位、40Msps、1.8V ADC，串行LVDS輸出 |
| 文件頁數： | 22/25頁 |
| 文件大小： | 790K |
| 代理商： | MAX1126 |
M
Quad, 12-Bit, 40Msps, 1.8V ADC with
S erial LV DS Outputs
22
______________________________________________________________________________________
Global Power-Down (PDALL)
PDALL controls the power-down mode of all channels
and the internal reference circuitry. Drive PDALL high to
enable global power-down. In global power-down mode,
the output impedance of all the LVDS/SLVS outputs is
approximately 378
, if DT is low. The output impedance
of the differential LVDS/SLVS outputs is 100
when DT is
high. See the
Electrical Characteristics
table for typical
supply currents with global power-down. The following
list shows the state of the analog inputs and digital out-
puts in global power-down mode:
IN_P, IN_N analog inputs are disconnected from the
internal input amplifier.
REFIO has >1M
resistance to GND.
OUT_P, OUT_N, CLKOUTP, CLKOUTN, FRAMEP,
and FRAMEN have approximately 378
between the
output pairs when DT is low. When DT is high, the dif-
ferential output pairs have 100
between each pair.
When operating from the internal reference, the wake-
up time from global power-down is typically 132μs.
When using an external reference, the wake-up time is
dependent on the external reference drivers.
Applic ations Information
Using T ransformer Coupling
An RF transformer (Figure 9) provides an excellent
solution to convert a single-ended input source signal
to a fully differential signal, required by the MAX1126
for optimum performance. The MAX1126 input com-
mon-mode voltage is internally biased to 0.6V (typ) with
f
CLK
= 40MHz. Although a 1:1 transformer is shown, a
step-up transformer can be selected to reduce the
drive requirements. A reduced signal swing from the
input driver, such as an op amp, can also improve the
overall distortion.
Grounding, Bypassing, and Board Layout
The MAX1126 requires high-speed board layout design
techniques. Refer to the MAX1127 EV kit data sheet for
a board layout reference. Locate all bypass capacitors
as close to the device as possible, preferably on the
same side as the ADC, using surface-mount devices
for minimum inductance. Bypass AV
DD
to GND with a
0.1μF ceramic capacitor in parallel with a
≥
2.2μF
ceramic capacitor. Bypass OV
DD
to GND with a 0.1μF
ceramic capacitor in parallel with a
≥
2.2μF ceramic
capacitor. Bypass CV
DD
to GND with a 0.1μF ceramic
capacitor in parallel with a
≥
2.2μF ceramic capacitor.
Multilayer boards with ample ground and power planes
produce the highest level of signal integrity. Connect
MAX1126 ground pins and the exposed backside pad-
dle to the same ground plane. The MAX1126 relies on
the exposed backside paddle connection for a low-
inductance ground connection. Isolate the ground
plane from any noisy digital system ground planes.
Route high-speed digital signal traces away from the
sensitive analog traces. Keep all signal lines short and
free of 90° turns.
Ensure that the differential analog input network layout
is symmetric and that all parasitics are balanced equal-
ly. Refer to the MAX1126 EV kit data sheet for an exam-
ple of symmetric input layout.
Parameter Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from a straight line. For the
MAX1126, this straight line is between the end points of
the transfer function, once offset and gain errors have
been nullified. INL deviations are measured at every
step and the worst-case deviation is reported in the
Electrical Characteristics
table.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an
actual step width and the ideal value of 1 LSB. A DNL
error specification of less than 1 LSB guarantees no
missing codes and a monotonic transfer function. For
the MAX1126, DNL deviations are measured at every
step and the worst-case deviation is reported in the
Electrical Characteristics
table.
Offset Error
Offset error is a figure of merit that indicates how well
the actual transfer function matches the ideal transfer
function at a single point. For the MAX1126, the ideal
midscale digital output transition occurs when there is
-1/2 LSB across the analog inputs (Figures 6 and 7).
MAX1126
V
IN
0.1
μ
F
0.1
μ
F
N.C.
1
2
3
MINICIRCUITS
ADT1-1WT
6
5
4
T1
10
10
39pF
39pF
IN_P
IN_N
Figure 9. Transformer-Coupled Input Drive
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1126EGK | Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs |
| MAX11504 | Four-Channel, Standard-Definition Video Filter |
| MAX11505 | Four-Channel, Standard-Definition Video Filter |
| MAX1168EVC16 | MAX1168 Evaluation Kit/Evaluation System |
| MAX1168EVKIT | MAX1168 Evaluation Kit/Evaluation System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1126EGK | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs |
| MAX1126EGK+D | 制造商:Maxim Integrated Products 功能描述:ADC QUAD PIPELINED 40MSPS 12-BIT SERL 68QFN - Rail/Tube |
| MAX1126EGK+TD | 制造商:Maxim Integrated Products 功能描述:ADC QUAD PIPELINED 40MSPS 12-BIT SERL 68QFN - Tape and Reel |
| MAX1127 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Quad, 12-Bit, 65Msps, 1.8V ADC with Serial LVDS Outputs |
| MAX1127EGK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。