- 您現在的位置：買賣IC網 > PDF目錄2008 > MAX11210EEE+T (Maxim Integrated Products)ADC 24BIT 4WIRE SPI 16-QSOP PDF資料下載
參數資料
| 型號： | MAX11210EEE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | ADC 24BIT 4WIRE SPI 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 24 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 667mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
15
Maxim Integrated
24-Bit, Single-Channel, Ultra-Low-Power,
Delta-Sigma ADCs with GPIO
MAX11200/MAX11210
Command Byte
Communication between the user and the device is con-
ducted through SPI using a command byte. The com-
mand byte consists of two modes differentiated as com-
mand modes and data modes. Command modes and
data modes are further differentiated by decoding the
remaining bits in the command byte. The mode selected
is determined by the MODE bit. If the MODE bit is 0, then
the user is requesting either a conversion, calibration, or
power-down; see Table 5. If the MODE bit is 1, then the
user is selecting a data command and can either read
from or write to a register; see Table 6.
The Status register (STAT1) is a read-only register and
provides general chip operational status to the user. If
the user attempts to calibrate the system and overranges
the internal signal scaling, then a gain overrange condi-
tion is flagged with the SYSOR bit. The last data rate
programmed for the ADC is available in the RATE bits.
If the input signal has exceeded positive or negative full
scale, this condition is flagged with the OR and UR bits.
If the modulator is busy converting, then the MSTAT bit is
set. If a conversion result is ready for read-out, the RDY
bit is set; see Table 11.
The Control 1 register (CTRL1) is a read/write register,
and the bits determine the internal oscillator frequency,
unipolar or bipolar input range, selection of an internal or
external clock, enabling or disabling the reference and
input signal buffers, the output data format (offset binary
or two’s complement), and single-cycle or continuous
conversion mode. See Table 12.
The Control 2 register (CTRL2) is a read/write register,
and the bits configure the GPIOs as inputs or outputs
and their values. See Table 13.
The Control 3 register (CTRL3) is a read/write register,
and the bits determine the MAX11210 programmable
gain setting and the calibration register settings for both
the MAX11200 and MAX11210. See Table 14.
The Data register (DATA) is a read-only register. Data is
output from RDY/DOUT on the next 24 SCLK cycles once
CS is forced low. The data bits transition on the falling
edge of SCLK. Data is output MSB first, and is offset
binary or two’s complement, depending on the setting
of the FORMAT bit in the CTRL1 register. See Table 15.
The System Offset Calibration register (SOC) is a read/
write register, and the bits contain the digital value that
corrects the data for system zero scale. See Table 17.
The System Gain Calibration register (SGC) is a read/
write register, and the bits contain the digital value that
corrects the data for system full scale. See Table 18.
The Self-calibration Offset register (SCOC) is a read/
write register, and the bits contain the value that corrects
the data for chip zero scale. See Table 19.
The Self-calibration Gain register (SCGC) is a read/write
register, and the bits contain the value that corrects the
data for chip full scale. See Table 20.
Table 5. Command Byte (MODE = 0)
Table 6. Command Byte (MODE = 1)
Note: The START bit is used to synchronize the data from the host device. The START bit is always 1.
BIT
B7
B6
B5
B4
B3
B2
B1
B0
BIT NAME
START = 1
MODE = 1
0
RS3
RS2
RS1
RS0
W/R
BIT
B7
B6
B5
B4
B3
B2
B1
B0
BIT NAME
START = 1
MODE = 0
CAL1
CAL0
IMPD
RATE2
RATE1
RATE0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX11212BEUB+T | IC ADC 18BIT SRL 13.75SPS 10UMAX |
| MAX1135BCAP+ | IC ADC 16BIT 150KSPS 20-SSOP |
| MAX1138LEEE+T | IC ADC 10BIT SERIAL 16-QSOP |
| MAX1159AEUI+ | IC ADC 14BIT 135KSPS 28-TSSOP |
| MAX11602EEE+ | IC ADC SERIAL 8BIT 8CH 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11210EVKIT+ | 功能描述:數據轉換 IC 開發工具 EVKIT for MAX11210 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX11211 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:18-Bit, Single-Channel, Ultra-Low-Power, Delta-Sigma ADCs with Programmable Gain and GPIO |
| MAX11211EEE+ | 功能描述:模數轉換器 - ADC 18-Bit Delta-Sigma RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11211EEE+T | 功能描述:模數轉換器 - ADC 18-Bit Delta-Sigma RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11212 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:18-Bit, Single-Channel, Ultra-Low Power, Delta-Sigma ADC with 2-Wire Serial Interface |
發布緊急采購，3分鐘左右您將得到回復。