- 您現在的位置：買賣IC網 > PDF目錄9754 > MAX1112CPP+ (Maxim Integrated Products)IC ADC 8BIT LP 20-DIP PDF資料下載
參數資料
| 型號： | MAX1112CPP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT LP 20-DIP |
| 標準包裝： | 18 |
| 位數： | 8 |
| 采樣率（每秒）： | 50k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 680µW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 20-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 20-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個偽差分，單極；4 個偽差分，雙極 |
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
10
______________________________________________________________________________________
Table 3. Control-Byte Format
START
SEL2
SEL1
SEL0
UNI/BIP
SGL/DIF
PD1
PD0
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(MSB)
(LSB)
NAME
SGL/DIF
2
BIT
1 = single ended, 0 = differential. Selects single-ended or differential conversions. In single-
ended mode, input signal voltages are referred to COM. In differential mode, the voltage differ-
ence between two channels is measured (Tables 1 and 2).
DESCRIPTION
UNI/BIP
3
START
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode (Table 4).
PD0
0 (LSB)
7 (MSB)
1 = external clock mode, 0 = internal clock mode.
Selects external or internal clock mode.
The first logic “1” bit after CS goes low defines the beginning of the control byte.
SEL2
SEL1
SEL0
6
5
4
Select which of the input channels are to be used for the conversion (Tables 1 and 2).
PD1
1
1 = fully operational, 0 = power-down.
Selects fully operational or power-down mode.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
tACQ, is the minimum time needed for the signal to be
acquired. It is calculated by:
tACQ = 6 x (RS + RIN) x 18pF
where RIN = 6.5k
Ω, RS = the source impedance of the
input signal, and tACQ is never less than 1s. Note that
source impedances below 2.4k
Ω do not significantly
affect the AC performance of the ADC.
Input Bandwidth
The ADC’s input tracking circuitry has a 1.5MHz small-
signal bandwidth, so it is possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC’s sampling rate by
using undersampling techniques. To avoid high-
frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Inputs
Internal protection diodes, which clamp the analog
input to VDD and AGND, allow the channel input pins to
swing from (AGND - 0.3V) to (VDD + 0.3V) without dam-
age. However, for accurate conversions near full scale,
the inputs must not exceed VDD by more than 50mV or
be lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off channels over 2mA.
The MAX1112/MAX1113 can be configured for differen-
tial or single-ended inputs with bits 2 and 3 of the con-
trol byte (Table 3). In single-ended mode, analog inputs
are internally referenced to COM with a full-scale input
range from COM to VREFIN + COM. For bipolar opera-
tion, set COM to VREFIN/2.
In differential mode, choosing unipolar mode sets the
differential input range at 0V to VREFIN. In unipolar
mode, the output code is invalid (code zero) when a
negative differential input voltage is applied. Bipolar
mode sets the differential input range to ±VREFIN/2.
Note that in this mode, the common-mode input range
includes both supply rails. See Table 4 for input voltage
ranges.
Quick Look
To quickly evaluate the MAX1112/MAX1113’s analog
performance, use the circuit of Figure 5. The
MAX1112/MAX1113 require a control byte to be written
to DIN before each conversion. Tying DIN to +5V feeds
相關PDF資料 |
PDF描述 |
|---|---|
| MS27474T22B21SC | CONN RCPT 21POS JAM NUT W/SCKT |
| MAX1110EPP+ | IC ADC 8BIT LP 20-DIP |
| MS27468T23A35SB | CONN RCPT 100POS JAM NUT W/SCKT |
| MS3100F20-14S | CONN RCPT 5POS WALL MNT W/SCKT |
| MAX3480AEPI+ | IC RS485/RS422 DATA INTRFC 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1112CPP+ | 功能描述:模數轉換器 - ADC 5V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1112D | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs Internal 4.096V Reference |
| MAX1112EAP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1112EAP+ | 功能描述:模數轉換器 - ADC 5V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1112EAP+T | 功能描述:模數轉換器 - ADC 5V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。