- 您現在的位置：買賣IC網 > PDF目錄384648 > MAX1111 (Maxim Integrated Products, Inc.) +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs PDF資料下載
參數資料
| 型號： | MAX1111 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| 中文描述： | +2.7V、低功耗、多通道、串行8位ADC |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 284K |
| 代理商： | MAX1111 |
M
+2.7V, Low-Power, Multic hannel,
S erial 8-Bit ADCs
______________________________________________________________________________________
11
in control bytes of $FF (hex), which trigger single-
ended, unipolar conversions on CH7 (MAX1110) or
CH3 (MAX1111) in external clock mode without power-
ing down between conversions. In external clock mode,
the SSTRB output pulses high for two clock periods
before the most significant bit of the 8-bit conversion
result is shifted out of DOUT. Varying the analog input
alters the output code. A total of 10 clock cycles is
required per conversion. All transitions of the SSTRB
and DOUT outputs occur on SCLK’s falling edge.
How to S tart a Conversion
A conversion is started by clocking a control byte into
DIN. With
CS
low, each rising edge on SCLK clocks a bit
from DIN into the MAX1110/MAX1111’s internal shift reg-
ister. After
CS
falls, the first arriving logic “1” bit at DIN
defines the MSB of the control byte. Until this first start bit
arrives, any number of logic “0” bits can be clocked into
DIN with no effect. Table 3 shows the control-byte format.
The MAX1110/MAX1111 are compatible with MICROWIRE,
SPI, and QSPI devices. For SPI, select the correct clock
polarity and sampling edge in the SPI control registers:
set CPOL = 0 and CPHA = 0. MICROWIRE, SPI, and
QSPI all transmit a byte and receive a byte at the same
time. Using the Typical Operating Circuit (Figure 3), the
simplest software interface requires three 8-bit transfers
to perform a conversion (one 8-bit transfer to configure
the ADC, and two more 8-bit transfers to clock out the
8-bit conversion result). Figure 6 shows the MAX1110/
MAX1111 common serial-interface connections.
1μF
0.1μF
V
DD
DGND
AGND
CS
SCLK
DIN
DOUT
SSTRB
SHDN
+3V
N.C.
0.01μF
CH7 (CH3)
COM
REFOUT
REFIN
C1
1μF
0V TO
+2.048V
ANALOG
INPUT
OSCILLOSCOPE
CH1
CH2
CH3
CH4
*FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FF (HEX)
( ) ARE FOR THE MAX1111.
MAX1110
MAX1111
+3V
500kHz
OSCILLATOR
SCLK
SSTRB
DOUT*
Figure 5. Quick-Look Circuit
Table 4. Full-Scale and Zero-Scale Voltages
UNIPOLAR MODE
V
REFIN
+ COM
+V
REFIN
/ 2
+ COM
Full Scale
COM
COM
-V
REFIN
/ 2
+ COM
Positive
Full Scale
Zero Scale
Zero
Scale
BIPOLAR MODE
Negative
Full Scale
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1111CEE | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| MAX1111EEE | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| MAX1111EPE | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| MAX1111MJE | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| MAX1115 | Single-Supply, Low-Power, Serial 8-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11110 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2Msps/3Msps, Low-Power, Serial 12-/10-/8-Bit ADCs |
| MAX11110AUT+ | 制造商:Maxim Integrated Products 功能描述:SMALL, 2.2V TO 3.6V, LOW-POWER, 1-/2-CHANNEL, SERIAL, 8-/10- - Rail/Tube |
| MAX11110AUT+T | 功能描述:模數轉換器 - ADC 10Bit 1Ch 2Msps Serial RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11111 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2Msps/3Msps, Low-Power, Serial 12-/10-/8-Bit ADCs |
| MAX11111ATB+ | 制造商:Maxim Integrated Products 功能描述:SMALL, 2.2V TO 3.6V, LOW-POWER, 1-/2-CHANNEL, SERIAL, 8-/10- - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。