參數資料
| 型號： | MAX1110EPP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT LP 20-DIP |
| 標準包裝： | 18 |
| 位數： | 8 |
| 采樣率（每秒）： | 50k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 889mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 20-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 20-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；2 個差分，雙極 |
MAX1110/MAX1111
+2.7V, Low-Power, Multichannel,
Serial 8-Bit ADCs
______________________________________________________________________________________
15
SCLK
DIN
DOUT
CS
S
CONTROL BYTE 0
CONTROL BYTE 1
S
CONVERSION RESULT 0
B7
B0
B7
B0
B7
CONVERSION RESULT 1
CONVERSION RESULT 2
SSTRB
CONTROL BYTE 2
S
1
888
10
1
10
1
10
1
CONTROL BYTE 3
S
Figure 12a. Continuous Conversions, External Clock Mode, 10 Clocks/Conversion Timing
CS
SCLK
DIN
DOUT
S
CONTROL BYTE 0
CONTROL BYTE 1
S
CONVERSION RESULT 0
B7
B0
B7
CONVERSION RESULT 1
Figure 12b. Continuous Conversions, External Clock Mode, 16 Clocks/Conversion Timing
Data Framing
The falling edge of CS does not start a conversion. The
first logic high clocked into DIN is interpreted as a start
bit and defines the first bit of the control byte. A conver-
sion starts on the falling edge of SCLK, after the eighth
bit of the control byte (the PD0 bit) is clocked into DIN.
The start bit is defined as:
The first high bit clocked into DIN with CS low any
time the converter is idle; e.g., after VDD is applied.
OR
The first high bit clocked into DIN after the MSB of a
conversion in progress is clocked onto the DOUT
pin.
If CS is toggled before the current conversion is com-
plete, then the next high bit clocked into DIN is recog-
nized as a start bit; the current conversion is
terminated, and a new one is started.
The fastest the MAX1110/MAX1111 can run is 10
clocks per conversion. Figure 12a shows the serial-
interface timing necessary to perform a conversion
every 10 SCLK cycles in external clock mode.
Many microcontrollers require that conversions occur in
multiples of eight SCLK clocks; 16 clocks per conver-
sion is typically the fastest that a microcontroller can
drive the MAX1110/MAX1111. Figure 12b shows the
serial-interface timing necessary to perform a conver-
sion every 16 SCLK cycles in external clock mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27468T23A35SB | CONN RCPT 100POS JAM NUT W/SCKT |
| MS3100F20-14S | CONN RCPT 5POS WALL MNT W/SCKT |
| MAX3480AEPI+ | IC RS485/RS422 DATA INTRFC 28DIP |
| MC10LVEP16DG | IC RECEIVER/DRVR ECL DIFF 8SOIC |
| DS26522G+ | IC TXRX T1/E1/J1 DUAL 144CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1110EPP+ | 功能描述:模數轉換器 - ADC 2.7V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1110EVKIT | 功能描述:數據轉換 IC 開發(fā)工具 MAX1110 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1110EVL11-DIP | 功能描述:數據轉換 IC 開發(fā)工具 MAX1110L11-Dip Eval RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1110MJP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1111 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:+2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
發(fā)布緊急采購，3分鐘左右您將得到回復。