參數資料
型號: MAX1106CUB
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: ADC
英文描述: Single-Supply, Low-Power, Serial 8-Bit ADCs
中文描述: 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO10
封裝: UMAX-10
文件頁數: 12/16頁
文件大?。?/td> 205K
代理商: MAX1106CUB
Starting SCLK before conversion is complete corrupts
the conversion in progress, and the data clocked out at
DOUT does not represent the input signal. Bringing
CONVST high at anytime during a conversion or while
the data is clocked out will result in an incorrect conver-
sion. A new conversion can be restarted only if all eight
data bits of conversion have been clocked out. Toggle
CONVST after all data is clocked out to restart a new
conversion.
SHDN
is used to place the MAX1106/MAX1107 in low-
power mode (see Power-Down section). In this mode
DOUT is high impedance and any conversion in
progress is stopped immediately. If a conversion is
stopped by
SHDN
going low, the device must be reset
by waiting 35μs and clearing the output register with
eight SCLKs before the next conversion.
How to Perform a Conversion
The MAX1106/MAX1107 converts an input signal using
the internal clock. This frees the μP from the burden of
running the SAR conversion clock, and allows the con-
version results to be read back at the μP’s convenience
at any clock rate up to 2MHz.
Figures 6 and 7 show the serial interface timing charac-
teristics. CONVST idles low. Toggle CONVST high for at
least 1μs to perform the autozero adjustment. After
CONVST goes low, conversion starts immediately.
Allow 35μs for the internal conversion to complete and
issue the MSB of the conversion at DOUT. CONVST
needs to be held low once a conversion is started,
while SCLK should remain low during conversion for
best noise performance. An internal register stores data
when the conversion is in progress. SCLK clocks the
CONVST
SCLK
1
μ
s
(MIN)
HIGH-Z
HIGH-Z
DOUT
1
8
100
μ
s (MAX)
D7
MSB
LSB
D0
D6
D5
D4
D3
D2
D1
t
CONV
= 35
μ
s (MAX)
CONVERSION
ACQUISITION
t
CSPW
A/D STATE
ACQ
Figure 6. Conversion Timing Diagram
M
S ingle-S upply, Low-Power,
S erial 8-Bit ADCs
12
______________________________________________________________________________________
CONVST
SCLK
DOUT
I/O
SCK
MISO
+3V
SS
a) SPI
CONVST
SCLK
CONVST
SCLK
DOUT
CS
SCK
MISO
+3V
SS
b) QSPI
MAX1106
MAX1107
MAX1106
MAX1107
MAX1106
MAX1107
DOUT
I/O
SK
SI
c) MICROWIRE
Figure 5. Common Serial-Interface Connections
相關PDF資料
PDF描述
MAX1106EUB Single-Supply, Low-Power, Serial 8-Bit ADCs
MAX1107 Single-Supply, Low-Power, Serial 8-Bit ADCs
MAX1107EUB Single-Supply, Low-Power, Serial 8-Bit ADCs
MAX1111CPE +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs
MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs
相關代理商/技術參數
參數描述
MAX1106CUB+ 功能描述:模數轉換器 - ADC Single-Supply Low-P Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1106CUB+T 功能描述:模數轉換器 - ADC Single-Supply Low-P Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1106CUB-G07 制造商:Maxim Integrated Products 功能描述:+3V SINGLE-SUPPLY, LOW-POWER, SERIAL 8-BIT AD 10 PINS UMAX P - Bulk 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX1106CUBT 制造商:Maxim Integrated Products 功能描述:
MAX1106CUB-T 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32