參數資料
型號： MAX11041ETC+T
廠商： Maxim Integrated Products
文件頁數： 17/17頁
文件大?。?/td> 0K
描述： IC REMOTE CTRLR WIRED 12-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
應用： PDA，便攜式音頻/視頻，智能電話
接口： I²C
電源電壓： 1.6 V ~ 3.6 V
封裝/外殼： 12-WQFN 裸露焊盤
供應商設備封裝： 12-TQFN-EP（4x4）
包裝： 帶卷 (TR)
安裝類型： 表面貼裝
Reading the FIFO While the Key is Still Pressed
When a valid keypress occurs, INT goes low, signaling
to the processor that a key has been pressed (see
Figure 3). If the processor reads the FIFO while the key
is still pressed, the key type and current duration of the
keypress is sent. The current keypress information in
the FIFO is not cleared after a read operation if the key
is still pressed. In addition, after a read operation, if the
key is still pressed, INT goes high again until the device
detects another keypress/release, freeing the proces-
sor from polling. Conversely, if the processor chooses
to poll the duration of the keypress, INT stays high at
this time no matter how many times the processor
reads the FIFO. When INT goes low again (from anoth-
er keypress/release), key type and final time duration of
the keypress is available in the FIFO. When the FIFO is
read after the key release, the information from that
keypress is cleared and INT goes high again.
Reading the FIFO After the Key has Released
When a valid keypress occurs, INT goes low, signaling
to the processor that a key has been pressed (see
Figure 4). If the processor reads the FIFO after the key
has already been released (or an additional key was
pressed), the key type and final duration time of that
keypress is sent. In addition, the information from the
keypress is cleared and INT goes high again.
Digital Serial Interface
The MAX11041 contains an I2C-compatible interface for
data communication with a host processor (SCL and
SDA). The interface supports a clock frequency up to
400kHz. SCL and SDA require pullup resistors that are
connected to a positive supply. Figure 5 details the
read and write formats.
Write Format
The only write to the MAX11041 that is possible is to the
control register (C7–C0). Use the following sequence to
write to the control register (see Figure 5):
1) After generating a START condition (S), address the
MAX11041 by sending the appropriate slave
address byte with its corresponding R/W bit set to a
0 (see the
Slave Address and R/W Bit section). The
MAX11041 answers with an ACK bit (see the
Acknowledge Bits section).
2) Send the appropriate data bytes to program the
control register (C7–C0). The MAX11041 answers
with an ACK bit.
3) Generate a STOP condition (P).
Read Format
To read the control register and key type/duration stored
in FIFO, use the following sequence (see Figure 5):
1) After generating a START condition (S), address the
MAX11041 by sending the appropriate slave
address byte with its corresponding R/W bit set to a
1 (see the
Slave Address and R/W Bit section). The
MAX11041 answers with an ACK bit (see the
Acknowledge Bits section).
2) The MAX11041 sends the 8-bit chip ID I7–I0.
Afterwards, the master must send an ACK bit.
3) The MAX11041 sends the contents of the control
register (C7–C0) starting with the most significant
bit. Afterwards, the master must send an ACK bit.
MAX11041
Wired Remote Controller
____________________________________________________________________________________
9
START
ADDRESS
BYTE 0
ACK
STOP
5 BITS
0
ACK
START
ADDRESS
BYTE 0
R/
W
ACK
STOP
1
CHIP ID
BYTE 1
I7–I0
ACK
CONTROL
REG DATA
BYTE 2
ACK
KEY TYPE
BYTE 3
ACK
KEY
DURATION
BYTE 4
ACK
S
P
A
A1 A0
5 BITS
A1 A0
S
A
P
READ FORMAT
C7–C0
K7–K0
OF, T6–T0
R/
W
CONTROL
REG DATA
BYTE 1
C7–C0
WRITE FORMAT
SLAVE TO MASTER
MASTER TO SLAVE
Figure 5. Read/Write Formats
相關PDF資料
PDF描述
MAX11043ATL+T IC ADC 16BIT W/DAC 40-TQFN-EP
MAX11359AETL+T IC DAS SYSTEM 16BIT 40-TQFN
MAX115CAX+ IC DAS SYSTEM 12BIT 36-SSOP
MAX1221BETX+T IC ADC/DAC 12BIT W/FIFO 36TQFNEP
MAX1257BETM+T IC ADC/DAC 12BIT 48-TQFN
相關代理商/技術參數
參數描述
MAX11041有線遙控器 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
MAX11042 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX11042ETC+ 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Wired Remote Controllers
MAX11043 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:4-Channel, 16-Bit, Simultaneous-Sampling ADCs with PGA, Filter, and 8-/12-Bit Dual-Stage DAC
MAX11043ATL+ 功能描述:模數轉換器 - ADC 16Bit 4Ch Simul-Samp w/PGA & 8/12Bit D-S RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*