- 您現在的位置：買賣IC網 > PDF目錄2085 > MAX1088ETA+T (Maxim Integrated Products)IC ADC 10BIT 150KSPS 8-TDFN PDF資料下載
參數資料
| 型號： | MAX1088ETA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/15頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 150KSPS 8-TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 采樣率（每秒）： | 150k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1.6mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
and is available in MSB-first format. Observe the
SCLK to DOUT valid timing characteristic. Clock
data into the P on SCLK’s rising-edge.
SPI and MICROWIRE Interface
When using SPI interface (Figure 8a) or MICROWIRE
(Figure 8a and 8b), set CPOL = CPHA = 0. Two 8-bit
readings are necessary to obtain the entire 10-bit result
from the ADC. DOUT data transitions on the serial
clock’s falling edge and is clocked into the P on
SCLK’s rising edge. The first 8-bit data stream contains
the first 8-bits of DOUT starting with the MSB. The sec-
ond 8-bit data stream contains the remaining two result
bits (B1, B0) and two trailing sub-bits (S1, S0). DOUT
then goes high impedance.
QSPI Interface
Using the high-speed QSPI interface (Figure 9a) with
CPOL = 0 and CPHA = 0, the MAX1086–MAX1089
support a maximum fSCLK of 8MHz. One 8- to16-bit
reading is necessary to obtain the entire 10-bit result
from the ADC. DOUT data transitions on the serial
clock’s falling edge and is clocked into the P on
SCLK’s rising edge. The first 10 bits are the data and
the next two bits are sub-bits (S1, S0). DOUT then
goes high impedance (Figure 9b).
PIC16 and SSP Module and
PIC17 Interface
The MAX1086–MAX1089 are compatible with a
PIC16/PIC17 microcontroller (C), using the synchro-
nous serial port (SSP) module
To establish SPI communication, connect the controller
as shown in Figure 10a and configure the PIC16/PIC17
as system master. This is done by initializing its syn-
chronous serial port control register (SSPCON) and
synchronous serial port status register (SSPSTAT) to
the bit patterns shown in Tables 1 and 2.
In SPI mode, the PIC16/PIC17 Cs allow eight bits of
data to be synchronously transmitted and received
simultaneously. Two consecutive 8-bit readings (Figure
10b) are necessary to obtain the entire 10-bit result
from the ADC. DOUT data transitions on the serial
clock’s falling edge and is clocked into the C on
SCLK’s rising edge. The first 8-bit data stream contains
MAX1086–MAX1089
150ksps, 10-Bit, 2-Channel Single-Ended, and
1-Channel True-Differential ADCs in SOT23 and TDFN
______________________________________________________________________________________
11
Figure 8a. SPI Connections
Figure 8b. MICROWIRE Connections
CNVST
SCLK
DOUT
I/O
SCK
MISO
VDD
SS
SPI
MAX1086–
MAX1089
MAX1086–
MAX1089
CNVST
SCLK
DOUT
I/O
SK
SI
MICROWIRE
Table 1. Detailed SSPCON Register Content
CONTROL BIT
MAX1086–MAX1089
SETTINGS
SYNCHRONOUS SERIAL PORT CONTROL REGISTER (SSPCON)
WCOL
Bit 7
X
Write Collision Detection Bit
SSPOV
Bit 6
X
Receive Overflow Detect Bit
SSPEN
Bit 5
1
Synchronous Serial Port Enable Bit.
0: Disables serial port and configures these pins as I/O port pins.
1: Enables serial port and configures SCK, SDO and SCI pins as serial port pins.
CKP
Bit 4
0
Clock Polarity Select Bit. CKP = 0 for SPI master mode selection.
SSPM3
Bit 3
0
SSPM2
Bit 2
0
SSPM1
Bit 1
0
SSPM0
Bit 0
1
Synchronous Serial Port Mode Select Bit. Sets SPI master mode and selects
fCLK= fOSC / 16.
X = Don’t care
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1090AEEI+ | IC ADC 10BIT 400KSPS 28-QSOP |
| MAX1106EUB+T | IC ADC 8BIT LP 10-UMAX |
| MAX1108EUB+TG07 | IC ADC 8BIT SPI/SRL 50K 10UMAX |
| MAX110AEWE+ | IC ADC 14BIT 2CH 16-SOIC |
| MAX11131ATI+ | IC ADC 12BIT SRL 28-TQFN-EP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1088EVKIT | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Evaluation Kit and Evaluation System for the MAX1286/MAX1288/MAX1086/MAX1088 |
| MAX1089 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:150ksps.10-Bit.2-Channel Single-Ended.and 1-Channel True-Differential ADCs in SOT23 |
| MAX1089EKA | 制造商:Maxim Integrated Products 功能描述:150KSPS, 10-BIT, 1-CHANNEL TRUE-DIFFERENTIAL - Cut Tape Product |
| MAX1089EKA-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1089ETA+ | 制造商:Maxim Integrated Products 功能描述:150KSPS 10-BIT 2-CHANNEL SINGLE-ENDED AND 1-CHANNEL TRUE-DIF - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。